Logo
FULL SITE MENU

Recent content by LQR

  1. L

    1965 Evinrude 33hp Ski-Twin: Slipping out of Forward Gear.

    New prop installed and all is well. 👍😊 a "believer " I am. Thanks for the help!
  2. L

    1965 Evinrude 33hp Ski-Twin: Slipping out of Forward Gear.

    Would a missing thrust washer (item 50) cause excessive wear on the prop hub? This motor was missing that washer when I bought it....I have one on order with the prop.
  3. L

    1965 Evinrude 33hp Ski-Twin: Slipping out of Forward Gear.

    👌👍 ty!
  4. L

    1965 Evinrude 33hp Ski-Twin: Slipping out of Forward Gear.

    It definitely has a pressed rubber hub. This has GOT to be the problem. 🤞
  5. L

    1965 Evinrude 33hp Ski-Twin: Slipping out of Forward Gear.

    I found a nice Michigan Match 10 1/2 x 12 RH prop on ebay for $70. I think you're right. 🤦‍♂️. Makes the most sense since there is no "bang" or "thud" which would definitely be the case of metal on metal slipping were happening. Plus, I've replaced damn near the entire gear set! Lol! New prop...
  6. L

    1965 Evinrude 33hp Ski-Twin: Slipping out of Forward Gear.

    It's possible...... I'll pull it off and take another look. 👌 if this is the case, I'm assuming I just need a new prop, right?
  7. L

    1965 Evinrude 33hp Ski-Twin: Slipping out of Forward Gear.

  8. L

    1965 Evinrude 33hp Ski-Twin: Slipping out of Forward Gear.

    The pin shown in the screenshot goes through the prop and through the shaft.....no way for the prop to spin without shearing that pin....
  9. L

    1965 Evinrude 33hp Ski-Twin: Slipping out of Forward Gear.

    The engine RPMs kick up and I let of the throttle and it goes back into gear. No thud, it just breaks loose.....
  10. L

    1966 Johnson 33hp Super Seahorse - gear jumping out

    Great suggestion. My '65 Evinrude 33hp SkiTwin fwd gear is skipping after replacing clutch dog, fork and forward gear....frustrating it is still slipping! Going to lossen both ends if the shift rod Connector and make sure the bolts engage the notches.
  11. L

    1965 Evinrude 33hp Ski-Twin: Slipping out of Forward Gear.

    Yes, positive. It's pinned and capped with a coter pin. No way for it to slip....
  12. L

    1965 Evinrude 33hp Ski-Twin: Slipping out of Forward Gear.

    I was reading through my repair manual and I am going to take apart the shift rod connector and make sure the screws are lined up with the radii of the shift rod ends. I think my lower unit shift rod my not be up as far as it should, which means the upper shift rod connection may need...
  13. L

    1965 Evinrude 33hp Ski-Twin: Slipping out of Forward Gear.

    Also, what is this spring for and where does it install? When I opened the gear case it was nowhere to be found.....
  14. L

    1966 33hp evinrude need advice

    I have a 1965 33hp Ski-Twin and changing the clutch dog is fairly simple. Check on YouTube for a tutorial, but you need to remove the lower unit. There should be a small oval cover with two screws on the side of the shaft. Open that up and loosen the lower screw on the brass connector to allow...
  15. L

    1965 Evinrude 33hp Ski-Twin: Slipping out of Forward Gear.

    Old clutch dog and forward gear.
See more
Back
Top