Current visitors

Welcome to the updated forum! Existing members please log in with your current user name and password, or use the forgot password option. Visitors, please register to join in.

faztbullet

Silver Medal Contributor From tennessee

Joined: Nov 27, 2011

Last seen: 47 minutes ago Viewing thread Mercury Blackmax 150 hp boggs out when in gear and trying to accelerate

Latest activity Postings About

- faztbullet replied to the thread 40hp magnum compression.
  
  Selco manuals are good for emergency toilet paper at best. That motor should have a minimum of 100psi if worn out
  
  47 minutes ago
- faztbullet replied to the thread Johnson 1998 50hp lower unit shimming.
  
  Shimming is done on driveshaft pinion height and done with special tool
  
  Today at 5:24 AM
- faztbullet replied to the thread 40hp magnum compression.
  
  That is the primer choke
  
  Yesterday at 6:28 PM
- faztbullet replied to the thread Mercury Blackmax 150 hp boggs out when in gear and trying to accelerate.
  
  Mercury has never designed or made a V-6 outboard that operated this way. Your problem was a bias circuit bad in switchbox, if you didnt...
  
  Tuesday at 10:53 PM
- faztbullet replied to the thread 40hp magnum compression.
  
  Check with different gauge
  
  Tuesday at 10:46 PM
- faztbullet replied to the thread Overheating issue?.
  
  Remove the oil pressure sensor and test oil pressure...should be 4psi+ at 1000rpm and 21psi+ at 5000rpm
  
  Tuesday at 10:45 PM
- faztbullet replied to the thread Installing temperature sender on 1986 75 hp Merc 2 stroke, 4 Cyl.
  
  Gauge will be instant reading vs a sensor
  
  Tuesday at 10:20 PM
- faztbullet replied to the thread Overheating issue?.
  
  Could have worn the internal bearings and oil pressure is now low.
  
  Tuesday at 7:56 AM
- faztbullet replied to the thread Installing temperature sender on 1986 75 hp Merc 2 stroke, 4 Cyl.
  
  That a restriction cooling system and you would hardly see gauge move, better to install a 15psi water pressure gauge. It will go in...
  
  Tuesday at 7:53 AM
- faztbullet replied to the thread 2005 mercury 150 efi lower unit installation problem looks like rear bearing fell out..
  
  No..they either reinstalled the old one or didnt use loctite to install new one.
  
  Tuesday at 7:51 AM
- faztbullet replied to the thread What octane gas?.
  
  87 is fine
  
  Monday at 9:00 PM
- faztbullet replied to the thread 2005 mercury 150 efi lower unit installation problem looks like rear bearing fell out..
  
  That is the crankshaft seal carrier and it keeps water out of crankshaft splines. It is a fairly common occurrence on V-6 models and...
  
  Monday at 8:59 PM
- faztbullet replied to the thread 350 omc cobra died while in motion.
  
  Upper drive took a dump
  
  Monday at 8:54 PM
- faztbullet replied to the thread 1998 evinrude 225 stalls during acceleration..
  
  Didn't flip the idle and intermediate jets did ya? Is this motor new to you?
  
  Monday at 8:51 PM
- faztbullet replied to the thread 2012 115 Evinrude etec.
  
  Better to use the software to test. CPS an flywheel should sync in 1-1/2 turn. You will see if with software.
  
  Monday at 8:48 PM
Show older items
Loading…
Loading…

Home
Members

Outboard Motor Parts

Inboard & Sterndrive Engine Parts

Manufacturer Catalogs

All Engine Brands

Outboard Repair Manuals

Inboard & Sterndrive Engine Manuals

Shop by Accessory Category

Please Note

Join the Forum

Discussion Topics

Outboard Motors

Inboard & Sterndrive Engines

Contact & About

Ordering

Returns

faztbullet

Latest activity Postings About