Quicksilver Marine Parts Catalog
- Contents
- Pre-1988 Mariner
- Mercury & Mariner
- Carburetor Kits
- Fuel Pump Repair Kits
- Ignition Keys
- Ignition Parts (2-Stroke)
- Ignition Parts (4-Stroke)
- Lower Unit Gearcase Seal
- Pistons
- Oil Filters
- Powerhead Gasket Sets
- Rod Main Bearings
- Solenoid Relay (2-Stroke)
- Solenoid Relay (4-Stroke)
- Spark Plugs (2-Stroke)
- Spark Plugs (4-Stroke)
- Stators
- Thermostat Kits
- Water Pump Parts (2-Stroke)
- Water Pump Parts (4-Stroke)
- Mercruiser
- Engine Parts
- View All »
- Alternators
- Camshafts, Bearings, Lifters & Push Rods
- Carburetors
- Connecting Rod Bearings
- Crankshaft Bearings
- Distributor Assembly & Components
- Distributor Gears
- ECMs, Coils, Wires & Spark Plugs
- Engine Couplers
- Engine Gaskets
- Exhaust Manifolds & Elbows
- Flame Arrestors
- Fuel Coolers
- Fuel Injection Components
- Fuel Pumps & Filters
- Ignition Tune-up Kits
- Intake & Exhaust Valves
- Oil Coolers
- Oil Pumps & Components
- Piston Rings
- Pistons
- Rocker Arms & Hardware
- Starter Parts
- Starters & Solenoids
- Thermostats, Housings & Covers
- Timing Chains & Gears
- Valve Caps, Springs & Keepers
- V-Belts & Serpentine Belts
- Water Hoses—Engine Supply
- Water Hoses—Exhaust Cooling
- View All »
- Transom & Drive Parts
- View All »
- Bearing Carriers
- Bellows
- Drive Shaft Housing & Sterndrive Units
- Drive Shaft Housing Bearings
- Drive Shaft Housing Gears
- Gear Case Bearings
- Gear Case Gears
- Gear Case Seals
- Gear Case Shafts
- Gear Case Shims
- Gimbal Bearings
- Installation Gaskets
- Trim Cylinders
- Trim Cylinder Hardware
- Trim Cylinder Hoses
- Universal Joints (U-Joints)
- Water Pump Impellers & Kits
- View All »
- Engine Parts
- Page Numbers
ENGINE ACCESSORIES
GEAR LUBE MONITOR KIT
BEARING KIT
GIMBAL BEARING KIT
Mounts on inner transom, connecting internally to the upper driveshaft housing.
Includes low gear lube warning sensor that connects to the engine audio warning
system. Warning feature requires that the Audio Warning System is installed on the
engine.
Perma‑Lube Bearing Kit required to retrofit the new XR/XZ drives to older Bravo
transom plate assemblies to provide enough clearance for the larger u‑joint on the
Fits Alpha One Gen II (s/n 0D491000 and above).
new XR/XZ drives.
GEAR LUBE RESERVOIR KIT
Fits Bravo transom assemblies
TRAILERING CLIPS
To support drive in the tilt up position while trailering.
TRAILERING CLIP
1 quart reservoir kit with float switch.
Designed to replace the smaller rectangular reservoir for added gear lube capacity.
Fits Bravo drives running under excessive loads in a heavy use environment.
GEAR LUBE RESERVOIR RELOCATION KIT
Fits MC‑I, R, MR, Alpha, Bravo & Vazer drives.
Priced & packaged in qty. of 2
Quicksilver Branded, Clamshell Package Point of Sale Packaged.
GEAR LUBE MONITOR KITS
GEAR LUBE MONITOR KIT
Reservoir Relocation Kit. Used to relocate the "square" reservoir bottle from the
engine to the transom. This kit should be used when the installation of any other
accessory kit would interfere with the reservoir at its factory installed location.
Fits Alpha & Bravo models (1994 and newer)
Mounts on inner transom and connects to the vent hole in the upper driveshaft
housing.
Fits MC‑I, R, MR, & Alpha One drives (s/n 0D490999 and below).
US Quicksilver Product Guide
1193