Quicksilver Marine Parts Catalog
- Contents
- Pre-1988 Mariner
- Mercury & Mariner
- Carburetor Kits
- Fuel Pump Repair Kits
- Ignition Keys
- Ignition Parts (2-Stroke)
- Ignition Parts (4-Stroke)
- Lower Unit Gearcase Seal
- Pistons
- Oil Filters
- Powerhead Gasket Sets
- Rod Main Bearings
- Solenoid Relay (2-Stroke)
- Solenoid Relay (4-Stroke)
- Spark Plugs (2-Stroke)
- Spark Plugs (4-Stroke)
- Stators
- Thermostat Kits
- Water Pump Parts (2-Stroke)
- Water Pump Parts (4-Stroke)
- Mercruiser
- Engine Parts
- View All »
- Alternators
- Camshafts, Bearings, Lifters & Push Rods
- Carburetors
- Connecting Rod Bearings
- Crankshaft Bearings
- Distributor Assembly & Components
- Distributor Gears
- ECMs, Coils, Wires & Spark Plugs
- Engine Couplers
- Engine Gaskets
- Exhaust Manifolds & Elbows
- Flame Arrestors
- Fuel Coolers
- Fuel Injection Components
- Fuel Pumps & Filters
- Ignition Tune-up Kits
- Intake & Exhaust Valves
- Oil Coolers
- Oil Pumps & Components
- Piston Rings
- Pistons
- Rocker Arms & Hardware
- Starter Parts
- Starters & Solenoids
- Thermostats, Housings & Covers
- Timing Chains & Gears
- Valve Caps, Springs & Keepers
- V-Belts & Serpentine Belts
- Water Hoses—Engine Supply
- Water Hoses—Exhaust Cooling
- View All »
- Transom & Drive Parts
- View All »
- Bearing Carriers
- Bellows
- Drive Shaft Housing & Sterndrive Units
- Drive Shaft Housing Bearings
- Drive Shaft Housing Gears
- Gear Case Bearings
- Gear Case Gears
- Gear Case Seals
- Gear Case Shafts
- Gear Case Shims
- Gimbal Bearings
- Installation Gaskets
- Trim Cylinders
- Trim Cylinder Hardware
- Trim Cylinder Hoses
- Universal Joints (U-Joints)
- Water Pump Impellers & Kits
- View All »
- Engine Parts
- Page Numbers
DRIVE SYSTEMS
UPPER GEAR KIT
UPPER GEAR KIT
16‑20 teeth, 1.32 ratio
17‑19 teeth, 1.84/1.81 ratio
Fits MC‑I, R, MR, Alpha One & SS (1975‑1990)
Fits MC‑I, R, MR, Alpha One & Gen II (s/n 0K999999 and below) (1976‑1997)
UPPER GEAR KIT
UPPER GEAR KIT
20‑24 teeth, 1.98/1.94 & 2.40 ratio
For use w/ heavy duty 1.50 gears only. The HD 1.50 drive gear has a stepped
bearing surface requiring the use of a special bearing kit having 2 different I.D.
Fits MC‑I, R, MR, Alpha One & Gen II (s/n 0K999999 and below) (1970‑1997)
bearings.
Fits MR, Alpha One & SS (1984‑1990)
UPPER GEAR KIT
UPPER GEAR KIT
20‑22 teeth, 1.47 ratio
Fits Alpha One Gen II (s/n 0L000040 and above) (1998 & newer)
20‑22 teeth, 1.50/1.47 ratio
Fits MC‑I, R, MR, Alpha One & Gen II (s/n 0K999999 and below) (1971‑1997)
UPPER GEAR KIT
UPPER GEAR KIT
24‑24 teeth, 1.62 & 2.00 ratio
Fits Alpha One Gen II (s/n 0L000040 and above) (1998 & newer)
24‑24 teeth, 1.65/1.62 ratio
Fits MC‑I, R, MR, Alpha One & Gen II (s/n 0K999999 and below) (1970‑1997)
US Quicksilver Product Guide
1115