Quicksilver Marine Parts Catalog
- Contents
- Pre-1988 Mariner
- Mercury & Mariner
- Carburetor Kits
- Fuel Pump Repair Kits
- Ignition Keys
- Ignition Parts (2-Stroke)
- Ignition Parts (4-Stroke)
- Lower Unit Gearcase Seal
- Pistons
- Oil Filters
- Powerhead Gasket Sets
- Rod Main Bearings
- Solenoid Relay (2-Stroke)
- Solenoid Relay (4-Stroke)
- Spark Plugs (2-Stroke)
- Spark Plugs (4-Stroke)
- Stators
- Thermostat Kits
- Water Pump Parts (2-Stroke)
- Water Pump Parts (4-Stroke)
- Mercruiser
- Engine Parts
- View All »
- Alternators
- Camshafts, Bearings, Lifters & Push Rods
- Carburetors
- Connecting Rod Bearings
- Crankshaft Bearings
- Distributor Assembly & Components
- Distributor Gears
- ECMs, Coils, Wires & Spark Plugs
- Engine Couplers
- Engine Gaskets
- Exhaust Manifolds & Elbows
- Flame Arrestors
- Fuel Coolers
- Fuel Injection Components
- Fuel Pumps & Filters
- Ignition Tune-up Kits
- Intake & Exhaust Valves
- Oil Coolers
- Oil Pumps & Components
- Piston Rings
- Pistons
- Rocker Arms & Hardware
- Starter Parts
- Starters & Solenoids
- Thermostats, Housings & Covers
- Timing Chains & Gears
- Valve Caps, Springs & Keepers
- V-Belts & Serpentine Belts
- Water Hoses—Engine Supply
- Water Hoses—Exhaust Cooling
- View All »
- Transom & Drive Parts
- View All »
- Bearing Carriers
- Bellows
- Drive Shaft Housing & Sterndrive Units
- Drive Shaft Housing Bearings
- Drive Shaft Housing Gears
- Gear Case Bearings
- Gear Case Gears
- Gear Case Seals
- Gear Case Shafts
- Gear Case Shims
- Gimbal Bearings
- Installation Gaskets
- Trim Cylinders
- Trim Cylinder Hardware
- Trim Cylinder Hoses
- Universal Joints (U-Joints)
- Water Pump Impellers & Kits
- View All »
- Engine Parts
- Page Numbers
COOLING SYSTEM
HOSE - MOLDED
HOSE - MOLDED
Fuel cooler to oil cooler, 1‑1/4 in. (32 mm) I.D.
Oil cooler to oil cooler
1‑1/4 in. (32 mm) I.D.
Use with 10 in. long oil cooler
Fits 330/340/7.4L MIE
Fits 7.4L & 8.2L MPI MIE, 454 Mag & 502 Mag
HOSE - MOLDED
HOSE - MOLDED
Oil cooler to oil cooler
Oil cooler to oil cooler
1‑1/4 in. (32 mm) I.D.
1‑1/4 in. (32 mm) I.D.
Fits 7.4L/8.2L MPI MIE, 454 Mag & 502 Mag
Fits 7.4L MIE
HOSE - MOLDED
HOSE - MOLDED
Oil cooler to oil cooler, 1‑1/4 in. (32 mm) I.D.
Cooler to thermostat housing
1‑1/4 in. (32 mm) I.D.
Use with 13 in. long engine oil cooler
Fits 7.4L & 8.2L MPI MIE, 454 Mag & 502 Mag with VST fuel system
Fits 7.4L
HOSE - MOLDED
HOSE - MOLDED
Fuel cooler to oil cooler, 1‑1/4 in. (32 mm) I.D.
Cooler to thermostat housing
1‑1/4 in. (32 mm) I.D.
Use with 13 in. long engine oil cooler
Fits 7.4L & 8.2L MPI MIE, 454 Mag & 502 Mag with fuel cooled system
Fits 454 Mag
US Quicksilver Product Guide
877