Quicksilver Marine Parts Catalog
- Contents
- Pre-1988 Mariner
- Mercury & Mariner
- Carburetor Kits
- Fuel Pump Repair Kits
- Ignition Keys
- Ignition Parts (2-Stroke)
- Ignition Parts (4-Stroke)
- Lower Unit Gearcase Seal
- Pistons
- Oil Filters
- Powerhead Gasket Sets
- Rod Main Bearings
- Solenoid Relay (2-Stroke)
- Solenoid Relay (4-Stroke)
- Spark Plugs (2-Stroke)
- Spark Plugs (4-Stroke)
- Stators
- Thermostat Kits
- Water Pump Parts (2-Stroke)
- Water Pump Parts (4-Stroke)
- Mercruiser
- Engine Parts
- View All »
- Alternators
- Camshafts, Bearings, Lifters & Push Rods
- Carburetors
- Connecting Rod Bearings
- Crankshaft Bearings
- Distributor Assembly & Components
- Distributor Gears
- ECMs, Coils, Wires & Spark Plugs
- Engine Couplers
- Engine Gaskets
- Exhaust Manifolds & Elbows
- Flame Arrestors
- Fuel Coolers
- Fuel Injection Components
- Fuel Pumps & Filters
- Ignition Tune-up Kits
- Intake & Exhaust Valves
- Oil Coolers
- Oil Pumps & Components
- Piston Rings
- Pistons
- Rocker Arms & Hardware
- Starter Parts
- Starters & Solenoids
- Thermostats, Housings & Covers
- Timing Chains & Gears
- Valve Caps, Springs & Keepers
- V-Belts & Serpentine Belts
- Water Hoses—Engine Supply
- Water Hoses—Exhaust Cooling
- View All »
- Transom & Drive Parts
- View All »
- Bearing Carriers
- Bellows
- Drive Shaft Housing & Sterndrive Units
- Drive Shaft Housing Bearings
- Drive Shaft Housing Gears
- Gear Case Bearings
- Gear Case Gears
- Gear Case Seals
- Gear Case Shafts
- Gear Case Shims
- Gimbal Bearings
- Installation Gaskets
- Trim Cylinders
- Trim Cylinder Hardware
- Trim Cylinder Hoses
- Universal Joints (U-Joints)
- Water Pump Impellers & Kits
- View All »
- Engine Parts
- Page Numbers
STEERING
STEERING ARM EXTENSION KIT
ATTACHING KIT
Used with dual engine tie bar kits. Not designed for use with hydraulic or power
Port cable entry.
steering systems or as a primary steering attachment point.
Fits Mercury/Mariner 6/8/9.9/15 hp. (2 cyl.) 2 cycle outboards (USA 0A197112 and
Fits Mercury/Mariner 70/75/80 hp. when installing a single cable‑dual engine tie bar
Newer, BEL 9461526 and Newer), 8 hp. 4‑Stroke outboards (232 cc) and 9.9 hp.
kit and included standard in a dual cable‑dual engine tie bar kit.
4‑Stroke outboards (0H000058‑0H016909).
ATTACHING KIT
CABLE SEAL KIT
SEAL KIT
Starboard cable entry.
Fits various Mercury/Mariner 25 thru 60 hp. and Force 40/50 hp. outboards. See
application chart for specific engine models.
ATTACHING KIT
Used in outboard applications.
Seals output end of tilt tube, helping to prevent corrosion of the RideGuide cable in
a thru tube steering arrangement.
RIDEGUIDE ATTACHING KITS
Through tilt tube type. When converting tiller handle steering to remote
steering, the existing co‑pilot friction control should be disabled or
removed.
ATTACHING KIT
Port cable entry.
Fits various Mercury/Mariner 25 thru 60 hp. and Force 40/50 hp. outboards. See
application chart for specific engine models.
Starboard cable entry.
Fits Mercury/Mariner 6/8/9.9/15 hp. (2 cyl.) 2 cycle outboards (USA 0A197112 and
Newer, BEL 9461526 and Newer), 8 hp. 4‑Stroke outboards (232 cc) and 9.9 hp.
4‑Stroke outboards (0H000058‑0H016909).
304