Quicksilver Marine Parts Catalog
- Contents
- Pre-1988 Mariner
- Mercury & Mariner
- Carburetor Kits
- Fuel Pump Repair Kits
- Ignition Keys
- Ignition Parts (2-Stroke)
- Ignition Parts (4-Stroke)
- Lower Unit Gearcase Seal
- Pistons
- Oil Filters
- Powerhead Gasket Sets
- Rod Main Bearings
- Solenoid Relay (2-Stroke)
- Solenoid Relay (4-Stroke)
- Spark Plugs (2-Stroke)
- Spark Plugs (4-Stroke)
- Stators
- Thermostat Kits
- Water Pump Parts (2-Stroke)
- Water Pump Parts (4-Stroke)
- Mercruiser
- Engine Parts
- View All »
- Alternators
- Camshafts, Bearings, Lifters & Push Rods
- Carburetors
- Connecting Rod Bearings
- Crankshaft Bearings
- Distributor Assembly & Components
- Distributor Gears
- ECMs, Coils, Wires & Spark Plugs
- Engine Couplers
- Engine Gaskets
- Exhaust Manifolds & Elbows
- Flame Arrestors
- Fuel Coolers
- Fuel Injection Components
- Fuel Pumps & Filters
- Ignition Tune-up Kits
- Intake & Exhaust Valves
- Oil Coolers
- Oil Pumps & Components
- Piston Rings
- Pistons
- Rocker Arms & Hardware
- Starter Parts
- Starters & Solenoids
- Thermostats, Housings & Covers
- Timing Chains & Gears
- Valve Caps, Springs & Keepers
- V-Belts & Serpentine Belts
- Water Hoses—Engine Supply
- Water Hoses—Exhaust Cooling
- View All »
- Transom & Drive Parts
- View All »
- Bearing Carriers
- Bellows
- Drive Shaft Housing & Sterndrive Units
- Drive Shaft Housing Bearings
- Drive Shaft Housing Gears
- Gear Case Bearings
- Gear Case Gears
- Gear Case Seals
- Gear Case Shafts
- Gear Case Shims
- Gimbal Bearings
- Installation Gaskets
- Trim Cylinders
- Trim Cylinder Hardware
- Trim Cylinder Hoses
- Universal Joints (U-Joints)
- Water Pump Impellers & Kits
- View All »
- Engine Parts
- Page Numbers
STEERING
FITTING - 90 DEGREE
FITTING BULKHEAD 3 INCH
90 degree fitting used with compression style hydraulic sytems (1/4 ‑ 18 NPT to
Bulkhead fitting used with compression style steering hoses (.375 inch
3/8 compression)
compression X 3 inch LG)
Hydraulic Compression Steering systems
Hydraulic Compression Steering Systems
BULKHEAD FITTING - COMPRESSION STYLE
FITTING - TEE
Bulkhead fitting for Compression style Hydraulic Steering Systems
.375 x 2.50 inch
Compression Style Hydraulic Systems
FITTING - TEE
Used with Compression style hydraulic systems.
Tee ‑ 3/8 in. Compression X 3/8 in. male
Hydraulic Compression style systems ‑ Basic and Heavy Duty
FITTING - 90 DEGREE
Tee fitting used with compression style hydraulic sytem. (3/8 compression)
Hydraulic Compression Steering systems
FITTING - 1/4-18 NPTF TO 3/8 COMPRESSION
Used with Compression style hydraulic systems.
90 degree‑ 3/8 in. Compression X 3/8 in.male
Hydraulic Compression style systems ‑ Basic and Heavy Duty
REMOTE FILL KIT FOR HYDRAULIC STEERING
Fitting used with compression style hydraulic sytems (1/4 ‑ 18 NPTF to 3/8
compression)
Hydraulic Compression Steering systems
FITTING-TEE BLEEDER 3/8 COMP X 6 ORFS
Remote fill adapter for rear mount and tilt mount Hydraulic pumps
Hydraulic Steering for Verado 135 to 200‑4 stroke engines
Tee fitting used on the compression style cylinders (1500 PSI)
Also can be used on OptiMax with Mercury hydraulic cylinder and hoses
288