Parts for Mariner 90 HP (3 Cylinder) Gear Housing (Drive Shaft) (6 Jaw Reverse Clutch)
Reference numbers in this diagram can be found in a light blue row below — scroll down to order.
# | 46-43024A 7 | W/P REPAIR KIT (1 required per assembly) |
46-43024A 7 - Water Pump Repair Kit [ More info ] Unavailable |
||
18-3214 - Impeller Repair Kit, Without Housing [ More info ] |
||
# | 26-43035A 4 | G/H SEAL KIT (1 required per assembly) |
# | 27-43004A90 | GASKET SET (1 required per assembly) |
27-43004A90 - Engine Gasket Set [ More info ] Unavailable |
||
#1 | 1667-9011G 8 | GEAR HOUSING (1 required per assembly) (BLACK) BASIC |
1667-9011G 8 - Gear Housing Assembly [ More info ] Unavailable |
||
#1 | 1667-9011G 9 | GEAR HOUSING (1 required per assembly) (GRAY) BASIC |
1667-9011G 9 - Gear Housing Assembly [ More info ] Unavailable |
||
1667-9011G60 - Ord 1667-9011G59 [ More info ] Unavailable |
||
#2 | 17-43043 | DOWEL PIN (FRONT) (1 required per assembly) |
#3 | 10-79953A 2 | DRAIN SCREW (2 required per assembly) |
10-79953A 2 - Drain Screw Kit [ More info ] Unavailable |
||
10-79953Q 2 - Screw Kit - Priced Individually [ More info ] Unavailable |
||
18-2244 - Plug Kit, 10-79953A2 [ More info ]
$3.59 $3.18 |
||
10-79953K04 - Drain Screw - Priced Individually [ More info ] |
||
#4 | 22-67892A 1 | SCREW (MAGNETIC) (1 required per assembly) |
22-67892A 1 - Drain Plug [ More info ] Unavailable |
||
22-67892A05 - Drain Plug Kit [ More info ] Unavailable |
||
22-67892A06 - Drain Plug Kit [ More info ] Unavailable |
||
22-8M0058389 - Screw Kit - Priced Individually [ More info ] |
||
#5 | 12-19183 | WASHER-SEALING (3 required per assembly) |
12-19183 - Washer (3/8 Inch Screw) [ More info ] Unavailable |
||
12-19183 2 - Washer - Priced Individually [ More info ] Unavailable |
||
12-19183Q02 - Seals, Pack of 4 (yes this is actually a pack of 4) [ More info ] |
||
#6 | 17-43044 | DOWEL PIN (REAR) (1 required per assembly) |
#7 | 31640 5 | TRIM TAB (1 required per assembly) |
31640 5 - 31640 5 - TRIM TAB [ More info ] Unavailable Replaced by 97-31640T 5 |
||
97-31640T 5 - 97-31640T 5 - TRIM TAB [ More info ] Unavailable Replaced by -31640T07 |
||
#8 | 10-825427 | SCREW (7/16-14 X 1-1/4) (1 required per assembly) |
#9 | 12-45176 | WASHER (1 required per assembly) |
#10 | 43040A 1 | CARRIER (1 required per assembly) |
43040A 1 - Carrier Assembly [ More info ] Unavailable |
||
#11 | 43046 | OILER TUBE (1 required per assembly) |
#12 | 826134 | ANODE (2 required per assembly) |
826134 - ANODE [ More info ] Unavailable |
||
97-826134Q - Anode, Aluminum, Outboard Side Pocket, Priced Individually [ More info ] |
||
97-826134T - Anode - Outboard Side Pocket - Priced Individually [ More info ] |
||
#13 | 10-40003 33 | SCREW (1 required per assembly) |
#14 | 11-826833 6 | NUT (1 required per assembly) |
11-826833 6 - Nut , Priced Individually [ More info ] Unavailable |
||
11-40144 - NUT Note: Priced Individually [ More info ] Unavailable |
||
#15 | 43-44484 | PINION GEAR (ALSO PART OF 43-850033A2)(13 TEETH) (1 required per assembly) |
43-44484 - Gear, Pinion (13 Teeth) (2.31:1 Ratio) [ More info ] Unavailable |
||
#16 | 11-35921 | NUT (1 required per assembly) |
18-2359 - Nut Kit [ More info ]
$5.19 $2.97 |
||
#17 | 850307 | SHIFT CAM (1 required per assembly) |
#18 | 31-42677A 1 | TAPERED ROLLER BEARING (1 required per assembly) |
#19 | 15-44492A 1 | SHIM ASSEMBLY (1 required per assembly) |
#20 | 45-43031A 1 | DRIVE SHAFT ASSEMBLY (1 required per assembly) (LONG-32 IN.) |
92-205-04-20A - Drive Shaft replaces 45-43031A 1 [ More info ] |
||
#20 | 45-43032A 6 | DRIVE SHAFT ASSEMBLY (1 required per assembly) (LL-34-1/2 IN.) |
#20 | 45-43032A 4 | DRIVE SHAFT ASSEMBLY (1 required per assembly) (X-LONG-37 IN.) |
92-205-04-25A - Drive Shaft replaces 45-43032A 4 [ More info ] |
||
#21 | 42461A 1 | WEAR SLEEVE ASSEMBLY (1 required per assembly) |
#22 | 43055A 4 | COVER ASSEMBLY (1 required per assembly) |
43055A 4 - NLA, New part # 46-8M0113262 [ More info ] Unavailable |
||
#23 | 27-43047 2 | GASKET (1 required per assembly) |
27-43047 2 - Gasket [ More info ] Unavailable |
||
#24 | 26-43036 | OIL SEAL (LOWER) (1 required per assembly) |
#25 | 26-43035 | OIL SEAL (UPPER) (1 required per assembly) |
#26 | 27-43033 1 | GASKET (1 required per assembly) |
#27 | 27-817277 | GASKET (1 required per assembly) |
27-817277 - Impeller Housing Gasket [ More info ] Unavailable |
||
#28 | 817275A 2 | WATER PUMP ASSEMBLY (1 required per assembly) |
#29 | 817276 | FACE PLATE (1 required per assembly) |
817276 - Face Plate, Water Pump [ More info ] Unavailable |
||
817276 1 - Water Pump Face Plate [ More info ] Unavailable |
||
#30 | 10-824832 7 | SCREW (M6 X 30) (4 required per assembly) |
10-824832 7 - Screw [ More info ] Unavailable |
||
#31 | 43023 2 | SEAL (1 required per assembly) |
#32 | 28-43037 | KEY (1 required per assembly) |
28-43037 - Key [ More info ] Unavailable |
||
28-8M0032833 - Key [ More info ] Unavailable |
||
#33 | 47-43026 2 | IMPELLER (1 required per assembly) |
47-43026 2 - Water Pump Impeller [ More info ] Unavailable |
||
#35 | 853906A 1 | SHIFT SHAFT ASSEMBLY (1 required per assembly) (LONG-12 IN.) |
#35 | 853907A 1 | SHIFT SHAFT ASSEMBLY (1 required per assembly) (LL-14-1/2 IN.) |
#35 | 853908A 1 | SHIFT SHAFT ASSEMBLY (1 required per assembly) (X-LONG-17 IN.) |
#36 | 53-29641 | E-RING (1 required per assembly) |
#37 | 23-43052A 4 | BUSHING ASSEMBLY (1 required per assembly) |
#38 | 25-45710 | O-RING (1 required per assembly) |
25-45710 - O-ring, (1.424 X .103), Reverse Lock Valve [ More info ] |
||
25-8M0204681 - O RING Note: Priced Individually [ More info ] |
||
#39 | 26-816464 1 | OIL SEAL (1 required per assembly) |
26-816464 1 - Seal [ More info ] Unavailable |
||
#40 | 10-824832 6 | SCREW (M6 X 25) (2 required per assembly) |