|
| Author |
Message |
    
Tim Brownell
New member
Username: timbillyosu
Post Number: 1
Registered: 07-2009
| | Posted on Wednesday, July 08, 2009 - 03:55 pm: | 
|
Just wanted to get the word out on a new Diesel engine. The engine is called a Buck Marine Diesel.
I work at Buck Marine Diesel. We are currently developing a prototype diesel engine specifically designed for inboard marine use. We're still working on things right now. We have the first prototype fully up and running.
We are currently working on a 6-cylinder model with 3- and 4-cylinder models to follow. The engines have a unique two injector per cylinder design that will increase the fuel mapping potential exponentially and result in lower emissions capability. The family of engines will range from 150 to 700 HP and have been designed from the bottom up with a totally different approach. These engines are capable of exceptional cooling, allowing for substantial improvements in power output while increasing longevity.
The cooling path for this engine is a fraction of most engines. In the classic designs, coolant flows into the front of the engine, all the way back to the rear cylinder, then back out the front. This means that the rear cylinder is always receiving water that has already been heated by the previous cylinders.
In the Buck Marine system, the coolant flows individually into and out of each cylinder. This means that the all of the cylinders will be operating at the same temperature at all times. Using individual and shorter cooling paths, will also help eliminate hot spots and temperature stacking.
The engine also has a dual cooling system that uses both an internal coolant as well as circulating raw water from whatever body of water the boat is in. This cooling system will keep the engine running cool, allowing us to generate more power. If a problem should arise, the engine is also very serviceable.
The modular cylinder design allows for easy maintenance. With our design, you can change an individual cylinder, head, piston, and connecting rod without having to remove the crank case. We are estimating that the entire upper half of the engine (cylinders, heads, pistons, and connecting rods ) could be entirely replaced in about 2 hours time. Each of the aforementioned parts is also interchangeable with each of the other cylinders. In addition, nearly every seal is made with an o-ring of some form, meaning that the gasket set for the entire engine can fit in a gallon-sized plastic bag. These two factors will significantly reduce part inventory. A video of the connecting rod replacement procedure is available on the website.
While running under a moderate load at about 2000 rpm, the exhaust temperatures were around 1000 degrees F. We ran under those conditions for about 15 minutes. The hottest that the coolant pump got was about 150 degrees F. None of the 6 heads were over 140 degrees and all of them were within about 5 degrees of one another. You could lay your hands on top of the valve covers.
Check out our website for further pictures and videos.
Feel free to ask any questions that you have.
http://www.buckdiesel.com
This video shows us tearing down and rebuilding a cylinder in under 8 minutes
http://www.youtube.com/v/ZnFOy5qtITc
Don't believe me? Watch it :-) |
|
|
|
Product Categories |
| Engine Parts · By Brand |
| Engine Manuals · By Brand |
| Books |
| General Repair and Maint. |
| Care and Repair |
| · Adhesive and Sealants |
| · Bottom Cleaners |
| · Cleaners Wax and Polish |
| · Mops Brushes and Sponges |
| Covers and Tops |
| · Bimini Tops · Hardware |
| · Cover Accessories |
| · Motor Covers |
| · Universal Boat Covers |
| Electronics |
| · Gauges and Compasses |
| · Mounts and Accessories |
| Electrical |
| · Batteries & Chargers |
| · Battery Accessories |
| · Dockside Electrical |
| · Electrical Terminals |
| · Electrical Wire, Cable |
| · Fuses, Fuse Holders |
| · Switches |
| · Wire Ties, Clips, Tape |
| Fuel Systems |
| · Fuel Tanks |
| · Fittings, Fills, Vents |
| · Hose & Primer Bulbs |
| · Filters, Senders, Caps |
| Hardware |
| · Deck Cabin Hardware |
| · Molding and Rub Rails |
| · Rails and Fittings |
| · Snaps Shackles and Hooks |
| · Windshield Hardware |
| Lighting |
| · Cabin Lights · Light Bulbs |
| · Navigation Light Parts |
| · Navigation Lights |
| · Spotlights · Parts |
| Mooring and Dock |
| · Boat Fenders · Boat Hooks |
| · Buoys and Markers |
| · Deck Cleats · Dock Edging |
| · Dock Parts and De-Icers |
| · Fender Covers and Holders |
| · Keelshield / Toon-Tectors |
| · Ladders and Platforms |
| Prop / Trim /
Transom |
| · Jack Plates, Wedges |
| · Mounting Brackets |
| · Outboard Stands |
| · Trim Tabs, Stablizers |
| · Prop Nuts, Locks, Pins |
| · Propellers · Wrenches |
| Pumps |
| · Aerator Pumps |
| · Bilge Pumps |
| · Drain Plugs and Tubes |
| · Hose · Through Hull Fittings |
| Rope and Cordage |
| · Anchor Line · Dock Line |
| · Fender Line · Bulk Rope |
| · Shock Cord and Bungee |
| Safety Products |
| · Horns Bells and Whistles |
| · Mirrors |
| · Vents Blowers and Hose |
| Sanitation |
| · Fresh Water Pumps |
| · Marine Toilets |
| · Sanitation Chemicals |
| · Sanitation Pumps/Hose |
| · Water/Waste System Parts |
| Seating |
| · Deck Chairs and Tables |
| · Fishing Seats |
| · Lounge Seats |
| · Pontoon Furniture |
| · Seat Bases and Pedestals |
| Steering / Control |
| · Control
Boxes |
| · Control
Cables |
| · Hydraulic
Steering |
| · Mechanical
Steering |
| · Rigging · Steering
Wheels |
| Tools / Shop Supplies |
| · Lubricants & Additives |
| · Motor Flushers |
| · Tools & Test Equipment |
| Trailering |
| · Boat Guides/Motor Support |
| · Hitches Balls Couplers |
| · Rollers Brackets Springs |
| · Tires Wheels and Carriers |
| · Trailer Hubs & Bearings |
| · Trailer Jacks |
| · Trailer Wiring and Lighting |
| · Winches Straps Tie Downs |
| Manufacturer List |
|
