MarineEngine.com - Your best connection for marine engines, parts, service, and information. View Cart / Check Out Contact MarineEngine.com Ordering and Shipping Information Free Engine Classifieds Engine Parts Discussion Board Engine Manuals Home / Directory
add bookmark or favorites | email this page
Topics Topics Edit Profile Profile Help/Instructions Help Member List Register  
Search Last 1|3|7 Days Search Search Tree View Tree View  

Housing seal replacement

Discussion Forum at MarineEngine.com » Johnson Evinrude Outboard » Archive through June 03, 2008 » Housing seal replacement « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Scott Sweebe
Visitor
Posted on Friday, May 30, 2008 - 11:29 am:   Edit Post Delete Post View Post/Check IP

I have a '74 25 hp evinrude that needs the seal between the bottom of the motor housing and the top of the lower unit. I found a seal available but am unsure just how far I need to tear down the motor to install this seal. It looks like a 1 piece seal which looks to be a little tough to install. A 2 piece seal would be a cinch but I don't think this is the case here.
Can anyone tell me what needs to be dismantled and just how far I have to go? I can figure it out I'm sure, but I am betting someone can simplify this for me a bit.
Thanks for any help with this.
Top of pagePrevious messageNext messageBottom of page Link to this message

Joe Reeves
Senior Member
Username: joereeves

Post Number: 6089
Registered: 02-2001


Posted on Friday, May 30, 2008 - 12:05 pm:   Edit Post Delete Post View Post/Check IP

I assume that you're speaking of the gasket that the powerhead sits upon.

You must remove the vertical throttle lever on the port side of the engine and the vertical shift lockout lever on the starboard side. Disconnect the incoming fuel line and any obvious wires that may be leading to a retaining location.
All that will be left is the powerhead retaining bolts/nuts/screws, whatever your engine uses.

When time permits, visit my eBay store at: http://stores.ebay.com/Evinrude-Johnson-Outboard-Parts-etc?refid=store
Top of pagePrevious messageNext messageBottom of page Link to this message

Scott Sweebe
Visitor
Posted on Friday, May 30, 2008 - 12:37 pm:   Edit Post Delete Post View Post/Check IP

It is called the housing to cover seal in the evinrude parts breakdown part #0308292. It seems that it is really an isolation gasket that the lower housing for the motor cover sits on to ab- sorb vibration. The lower housing sits on this seal which in turn sits on the very top of the lower unit. I believe it is a separate seal and not the powerhead to lower unit seal.
Thanks for the previous response and any further help.
Scott

Administration Administration Log Out Log Out   Previous Page Previous Page Next Page Next Page


Home / Directory | Engine Manuals | Engine Parts | Discussion Board | Free Classifieds | Orders / Shipping | Contact Us | View Cart

About Us | Terms of Use | Privacy Policy
MarineEngine.com, 184 Jones Dr., Brandon, VT 05733 USA
Phone: 802-247-4700 FAX: 802-301-1034 info@marineengine.com
Copyright © 2000 - 2007 by MarineEngine.com, Inc. All rights reserved
   
Traduca
EspanolEspanol
Traduisez
FrancaisFrancais
Traduza
PortuguesePortuguese
Traduca
Italiano
Ubersetzen
Deutschen
  
Sierra Marine Catalog
Seloc Online Manuals
Product Categories
Engine Parts · By Brand
Engine Manuals · By Brand
Books
General Repair and Maint.
Care and Repair
· Adhesive and Sealants
· Bottom Cleaners
· Cleaners Wax and Polish
· Mops Brushes and Sponges
Covers and Tops
· Bimini Tops   · Hardware
· Cover Accessories
· Motor Covers
· Universal Boat Covers
Electronics
· Gauges and Compasses
· Mounts and Accessories
Electrical
· Batteries & Chargers
· Battery Accessories
· Dockside Electrical
· Electrical Terminals
· Electrical Wire, Cable
· Fuses, Fuse Holders
· Switches
· Wire Ties, Clips, Tape
Fuel Systems
· Fuel Tanks
· Fittings, Fills, Vents
· Hose & Primer Bulbs
· Filters, Senders, Caps
Hardware
· Deck Cabin Hardware
· Molding and Rub Rails
· Rails and Fittings
· Snaps Shackles and Hooks
· Windshield Hardware
Lighting
· Cabin Lights · Light Bulbs
· Navigation Light Parts
· Navigation Lights
· Spotlights   · Parts
Mooring and Dock
· Boat Fenders · Boat Hooks
· Buoys and Markers
· Deck Cleats · Dock Edging
· Dock Parts and De-Icers
· Fender Covers and Holders
· Keelshield / Toon-Tectors
· Ladders and Platforms
Prop / Trim / Transom
· Jack Plates, Wedges
· Mounting Brackets
· Outboard Stands
· Trim Tabs, Stablizers
· Prop Nuts, Locks, Pins
 · Propellers · Wrenches
Pumps
· Aerator Pumps
· Bilge Pumps
· Drain Plugs and Tubes
· Hose · Through Hull Fittings
Rope and Cordage
· Anchor Line   · Dock Line
· Fender Line   · Bulk Rope
· Shock Cord and Bungee
Safety Products
· Horns Bells and Whistles
· Mirrors
· Vents Blowers and Hose
Sanitation
· Fresh Water Pumps
· Marine Toilets
· Sanitation Chemicals
· Sanitation Pumps/Hose
· Water/Waste System Parts
Seating
· Deck Chairs and Tables
· Fishing Seats
· Lounge Seats
· Pontoon Furniture
· Seat Bases and Pedestals
Steering / Control
· Control Boxes
· Control Cables
· Hydraulic Steering
· Mechanical Steering
· Rigging · Steering Wheels
Tools / Shop Supplies
· Lubricants & Additives
· Motor Flushers
· Tools & Test Equipment
Trailering
· Boat Guides/Motor Support
· Hitches Balls Couplers
· Rollers Brackets Springs
· Tires Wheels and Carriers
· Trailer Hubs & Bearings
· Trailer Jacks
· Trailer Wiring and Lighting
· Winches Straps Tie Downs
 Manufacturer List