MarineEngine.com - Your best connection for marine engines, parts, service, and information. View Cart / Check Out Contact MarineEngine.com Ordering and Shipping Information Free Engine Classifieds Engine Parts Discussion Board Engine Manuals Home / Directory
add bookmark or favorites | email this page
Topics Topics Edit Profile Profile Help/Instructions Help Member List Register  
Search Last 1|3|7 Days Search Search Tree View Tree View  

Newbie needs help

Discussion Forum at MarineEngine.com » Johnson Evinrude Outboard » Archive through May 18, 2008 » Newbie needs help « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

jeff darway
New member
Username: jeff6898

Post Number: 1
Registered: 05-2008
Posted on Saturday, May 17, 2008 - 12:25 pm:   Edit Post Delete Post View Post/Check IP

Just got my first boat. It is a 1981 Astroglass 16ft bass/ski boat. Has a 1979 Evinrude 85hp outboard model 85999R. The problem is on take off the front end comes up and is real slow to get up enough speed to level out. I was told the prop may be wrong for the boat. Any ideas? There is no markings on the prop to see what it is.
Top of pagePrevious messageNext messageBottom of page Link to this message

Joe Reeves
Senior Member
Username: joereeves

Post Number: 6026
Registered: 02-2001


Posted on Saturday, May 17, 2008 - 01:13 pm:   Edit Post Delete Post View Post/Check IP

First you must make sure that the engine itself is okay.

Compression should be 100+ psi and even on all cylinders. Is it?

With all of the spark plugs removed, the spark should jump a 1/4" gap on that model with a strong blue lightning like flame.... a real SNAP! Does it?

If the above tests prove those areas to be okay, then either you have the engine trimmed wrong (set too far back on the reverse lock rod). Looking at the boat on a trailer from a side view, the cavitation plate just above the propeller should be on the same plane (parallel) with the bottom of the boat..... OR

The carburetors are fouled causing the engine to run lean, in which case, they would need to be removed, cleaned, and rebuilt with complete carburetor kits..... OR

The propeller, as you suspect, could be a bad match for the boat. The diameter and pitch numbers would be on the face of the propeller in back of the prop nut and spacer assembly. If they're there, what are the numbers?

When time permits, visit my eBay store at: http://stores.ebay.com/Evinrude-Johnson-Outboard-Parts-etc?refid=store
Top of pagePrevious messageNext messageBottom of page Link to this message

jeff darway
New member
Username: jeff6898

Post Number: 2
Registered: 05-2008
Posted on Sunday, May 18, 2008 - 10:39 am:   Edit Post Delete Post View Post/Check IP

Borrowed a prop off a friends boat with same motor. Made a huge differance. Boat leveled out quick. Did check compression. All cylinders were at 130.

Administration Administration Log Out Log Out   Previous Page Previous Page Next Page Next Page


Home / Directory | Engine Manuals | Engine Parts | Discussion Board | Free Classifieds | Orders / Shipping | Contact Us | View Cart

About Us | Terms of Use | Privacy Policy
MarineEngine.com, 184 Jones Dr., Brandon, VT 05733 USA
Phone: 802-247-4700 FAX: 802-301-1034 info@marineengine.com
Copyright © 2000 - 2007 by MarineEngine.com, Inc. All rights reserved
   
Traduca
EspanolEspanol
Traduisez
FrancaisFrancais
Traduza
PortuguesePortuguese
Traduca
Italiano
Ubersetzen
Deutschen
  
Sierra Marine Catalog
Seloc Online Manuals
Product Categories
Engine Parts · By Brand
Engine Manuals · By Brand
Books
General Repair and Maint.
Care and Repair
· Adhesive and Sealants
· Bottom Cleaners
· Cleaners Wax and Polish
· Mops Brushes and Sponges
Covers and Tops
· Bimini Tops   · Hardware
· Cover Accessories
· Motor Covers
· Universal Boat Covers
Electronics
· Gauges and Compasses
· Mounts and Accessories
Electrical
· Batteries & Chargers
· Battery Accessories
· Dockside Electrical
· Electrical Terminals
· Electrical Wire, Cable
· Fuses, Fuse Holders
· Switches
· Wire Ties, Clips, Tape
Fuel Systems
· Fuel Tanks
· Fittings, Fills, Vents
· Hose & Primer Bulbs
· Filters, Senders, Caps
Hardware
· Deck Cabin Hardware
· Molding and Rub Rails
· Rails and Fittings
· Snaps Shackles and Hooks
· Windshield Hardware
Lighting
· Cabin Lights · Light Bulbs
· Navigation Light Parts
· Navigation Lights
· Spotlights   · Parts
Mooring and Dock
· Boat Fenders · Boat Hooks
· Buoys and Markers
· Deck Cleats · Dock Edging
· Dock Parts and De-Icers
· Fender Covers and Holders
· Keelshield / Toon-Tectors
· Ladders and Platforms
Prop / Trim / Transom
· Jack Plates, Wedges
· Mounting Brackets
· Outboard Stands
· Trim Tabs, Stablizers
· Prop Nuts, Locks, Pins
 · Propellers · Wrenches
Pumps
· Aerator Pumps
· Bilge Pumps
· Drain Plugs and Tubes
· Hose · Through Hull Fittings
Rope and Cordage
· Anchor Line   · Dock Line
· Fender Line   · Bulk Rope
· Shock Cord and Bungee
Safety Products
· Horns Bells and Whistles
· Mirrors
· Vents Blowers and Hose
Sanitation
· Fresh Water Pumps
· Marine Toilets
· Sanitation Chemicals
· Sanitation Pumps/Hose
· Water/Waste System Parts
Seating
· Deck Chairs and Tables
· Fishing Seats
· Lounge Seats
· Pontoon Furniture
· Seat Bases and Pedestals
Steering / Control
· Control Boxes
· Control Cables
· Hydraulic Steering
· Mechanical Steering
· Rigging · Steering Wheels
Tools / Shop Supplies
· Lubricants & Additives
· Motor Flushers
· Tools & Test Equipment
Trailering
· Boat Guides/Motor Support
· Hitches Balls Couplers
· Rollers Brackets Springs
· Tires Wheels and Carriers
· Trailer Hubs & Bearings
· Trailer Jacks
· Trailer Wiring and Lighting
· Winches Straps Tie Downs
 Manufacturer List