Logo
Click for Volvo Penta parts and manuals!
Results 1 to 4 of 4
  1. #1
    Join Date
    May 2007
    Location
    Washougal, Washington, USA
    Posts
    88

    Default Stray sparking from coil to distributor

    During warm up I noticed the tachometer needle was bouncing around and the starboard engine was starting to idle rough. I noticed there was arcing between the positive Pertronix wire from coil to side of the cast iron engine block half way to the Pertronix in the distributor. There wasn't any sign of bare wire or insulation on the two wires from coil to distributor. I had installed the Pertronix in both twin engines many years ago and have never had any issues! The engines are twin 1981 BB140A's. Does Pertronix wear out over time? I thought there is nothing to wear in a Pertronix system? Could it be a bad distributor cap, rotor, or coil? Probably the crimp splice has developed corrosion in it because I didn't cover it with a heat shrink tube wrap years ago when I installed it! Should I shield the wires? The arcing did not come from area around the crimp splice.

  2. #2
    Join Date
    Sep 2008
    Location
    Maryland - USA
    Posts
    8,669

    Default Re: Stray sparking from coil to distributor

    Arcing is typically caused by HIGH voltage, not the primary voltage....so I'd say you have a 'leak' from inside the cap/coil wire.

    If the cap(inside) and rotor look okay, make sure all of the high tension wires are seated and use a smear of silicone dielectric grease around the boots...

    you can also use a screwdriver - grounded with a jumper - to probe around all of the cap openings to 'find' the high voltage leak...

  3. #3
    Join Date
    Jun 2008
    Location
    Island Heights, NJ,
    Posts
    3,541

    Default Re: Stray sparking from coil to distributor

    While there is nothing to wear out in a Petronix system, caps and rotors still do.... My OEM HV ignition system in my boat never gets more than 2 (reliable) seasons out of a cap/rotor.

    HV wires have a finite life... Even the best OEM/Aftermarket ones start to degrade at about 10 seasons.
    Last edited by sandkicker; 04-09-2021 at 10:25 AM.
    Capt Bob
    1969 23ft ChrisCraft Lancer
    Merc 5.7L 260HP/ Volvo 280

  4. #4
    Join Date
    May 2007
    Location
    Washougal, Washington, USA
    Posts
    88

    Default Re: Stray sparking from coil to distributor

    I covered the two wires together with a black wire shield tube between the coil and distributor. It fixed the problem of the spark jumping to the engine block. I also just received new distributor caps and rotors today via Amazon. I'll install them and see if it also helps with the rough idle after warm up. As always the new spark plugs get black quickly! Older Sea Loc manual recommends .028 on the spark plug gap. I've been gapping them @.030 for the Pertronix. Could I be wrong? Does the wider gap produce a colder spark? Should I go back to .028? I have the timing set at 6 degrees BTDC and idle after warm up is around 900 rpm. If this doesn't fix the problem of engine dying on idle after warming up then I try using fresh fuel or blame the brand fricken new Weber/Redline K861kit I recently installed!

Similar Threads

  1. New distributor and coil for 318 starboard side
    By 74 Pacemaker 318s in forum Chrysler Inboard and Sterndrive Forum
    Replies: 0
    Last Post: 06-01-2018, 10:30 AM
  2. Wiring changes for new distributor & coil
    By joeld98 in forum Crusader Marine Engine Forum
    Replies: 3
    Last Post: 06-30-2010, 04:19 PM
  3. Pick up coil Est distributor
    By captnbill in forum Mercruiser Sterndrive Archive
    Replies: 8
    Last Post: 05-12-2009, 09:30 PM
  4. Overheating coil amp distributor
    By Jon Stern in forum Crusader Marine Archive
    Replies: 7
    Last Post: 04-05-2008, 10:15 AM
  5. Shifter stuck in drive after wrapping prop with stray line
    By tpm36 in forum Volvo Penta Gas Archive
    Replies: 1
    Last Post: 09-26-2006, 01:23 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •