Logo
FULL SITE MENU

Duoprop Volvo Penta drive 2000 GS drive oil change

N

Northernerbh

Guest
"Well maybe someone can help m

"Well maybe someone can help me with this. I cannot find the drain screw to change my drive oil before storage. I always had OMC and it was on the side. The diagram in my manual sort of points to an area behind the prop shaft housing, which means I need to remove the props.. Which I have never done. Any help would be appreciated. I am ussually pretty good at this stuff, but!!"
 
"<[img]"http://www.marineengin

"
32764.jpg
"
 
"From the Volvo manual:

Pro

"From the Volvo manual:

Propeller replacement — DP-S
Removing the propeller

This procedure requires you to use a special tool, Volvo PentaP/N 3855516.
1. Ignition switch must be OFF.
2. Make sure the remote control is in FORWARD to lock
the propeller shaft.
3. Remove the rear propeller nut.
4. Remove the rear propeller.
5. Change the remote control position to REVERSE to lock
the propeller shaft.
6. Remove the front propeller nut.
7. Remove the front propeller.
8. Wipe the propeller shaft clean. Inspect for fishing line;
remove if present.


Installing the propeller
CAUTION!
Failure to install all components could result in loss
of the propeller and damage to the drive unit the
next time the boat is operated.
1. Ignition switch must be OFF.
2. Make sure the remote control is in FORWARD.
3. Coat the full length of the propeller shaft and the insideof the propeller hub with Volvo Penta propeller shaft grease P/N 828250. (Removal of the propeller will be difficult if this is not done.)
4. Install the front propeller.
5. Install the front propeller nut and tighten it to 45 ft. lb. (60N·m).
6. Shift the remote control into REVERSE to lock the propeller shaft.
7. Install the rear propeller.
8. Install the rear propeller nut and tighten it to 50 ft. lb. (70 N·m).
9. Shift the remote control into NEUTRAL. The propeller should turn freely.




32771.jpg
"
 
"From the Volvo manual

Prop

"From the Volvo manual

Propeller replacement — DPX
Removing the propeller

This procedure requires you to use a special tool kit, Volvo
Penta P/N 885195.
1. Ignition switch must be OFF.
2. Make sure the remote control is in FORWARD to lock the propeller shaft.
3. Use the special tool (as shown) to remove the rear locking screw. Use a 30-mm socket to remove the propeller locking nut.
4. Remove the rear propeller.
5. Shift the remote control into REVERSE to lock the propeller shaft.
6. Use the special tool (as shown) to remove the front locking screw.
7. Remove the front propeller.
8. Wipe the propeller shaft clean. Inspect for fishing line; remove if present.

Installing the propeller
CAUTION!
Failure to install all components may result in loss of the propeller and damage to the drive unit the next time the boat is operated.
1. Ignition switch must be OFF.
2. Coat the full length of the propeller shaft and the inside of the propeller hub with Volvo Penta propeller shaft grease P/N 828250. (Removal of the propeller will be difficult if this is not done.)
3. Make sure the remote control is in FORWARD to lock the propeller shaft.
4. Install the front propeller.
5. Install the front propeller locking nut. Use the special tool to tighten the nut to 37 – 52 ft. lb. (50 – 70 N·m).
6. Shift the remote control into REVERSE to lock the propeller shaft.
7. Install the rear propeller.
8. Install the rear propeller locking nut (use a 30-mm socket). Tighten the nut to 19 – 26 ft. lb. (25 – 35 N·m).
9. Install the locking screw. Use the special tool to tighten the nut to 52 – 59 ft. lb. (70 – 80 N·m).
10. Shift the remote control into NEUTRAL. The propeller should turn freely.

32774.jpg
"
 
Back
Top