Logo
Click for Suzuki Manuals, Parts and Model Guides!
Results 1 to 11 of 11
  1. #1

    Default "Recently purchased used 1996

    "Recently purchased used 1996 DT 140 with jet pump... Mounted it onto boat took out for test drive found engine to be unresponsive to throttle and only achieved 4900 RPM. The compression is 130,125,130,120 top to bottom. The oil injection has been removed (not happy about that)and a coverr plate installed that was leaking. since repaired with no noticable difference. removed carbs found no issues. Have spark on all for holes. So I went to timing found that the engine was running 5 degrees all the time no adjustment??? Read in the manual that TVS, Engine speed, and water temp are only sensors. The TVS has 550 M ohms all of the time (any throttle position)I think this is my problem but,I am looking for information on specs for TVS and were to find oil injection system parts"

  2. #2
    superpole727's Avatar
    superpole727 Guest

    Default If it's a 1996 it should b

    If it's a 1996 it should be a voltage style tpi not a ohm output. You will need a manual to test properly. But if the timing is static at 5 degrees your on the right track.

  3. #3

    Default The TVS is not like an automot

    The TVS is not like an automotive TPS it reminds me of and off/on idle validaition switch. After taking in off of the engine I disassembled the switch and found a magnetic slid inside. No big suprise there but what was supprising to me was that the "ramp" that moved the slide was not gradual. for the first 30% of throttle open the magnetic slide does not move then for the rest of the throttle movement the ramp is one steady thickness and the slide is all the way pushed back. With all of that being said I agree that it is a 3 wire voltage reference sensor but my manual gives no specs for output in volts or does it give a static test for an ohms reading off of the engine. Thanks for the confidence that I am in the right direction (not bad for a big truck mechanic)

  4. #4
    superpole727's Avatar
    superpole727 Guest

    Default Hi Larry You can bench tes

    Hi Larry

    You can bench test it. I don't have a manual in front of me. You will probably need a factory manual. Is it square about 1" x 1" with a black rubber plug in the middle???

  5. #5
    superpole727's Avatar
    superpole727 Guest

    Default still here Larry???

    still here Larry???

  6. #6

    Default yes it is... 3 wire one ground

    yes it is... 3 wire one ground and a supply and signal I have too assume. If you could the reference voltage would be very helpful as well so that I know that my module is supplying the proper voltage for the sensor. The questions keep coming up in my head...Does the engine have to be running or will it supply referance voltage with just the key on because I did not have any voltage on either side of the plug on the engine harnas with the key on engine off. Are factory manuals available for these engines?

  7. #7
    superpole727's Avatar
    superpole727 Guest

    Default Is it square with a rubber plu

    Is it square with a rubber plug in the middle?

    That sensor works off of DC voltage. Be careful without a manual you can fry the rectifier circuit in the cdi box. It converts the ac voltage from flywheel into DC voltage for the TPI sensor. The idle setting is .5 volts. You need the manual. I still need the manual when I set those up.

  8. #8
    superpole727's Avatar
    superpole727 Guest

    Default sorry you did say yes it is sq

    sorry you did say yes it is square.

  9. #9
    superpole727's Avatar
    superpole727 Guest

    Default "You can bench test with a 12

    "You can bench test with a 12 volt source, test cord and of course service manual. If the timing is static there is a good chance it is bad. I'll price one for you Stand By"

  10. #10
    Join Date
    Feb 2009
    Location
    Conway, SC,
    Posts
    78

    Default "Larry, I have a used oil pump

    "Larry, I have a used oil pump off of an EFI engine but looking at the part numbers it doesn't look like it will work on the carbed '96 model."

  11. #11

    Default thanks still looking for a oil

    thanks still looking for a oil injection system minus oil tank.

    Larry

Similar Threads

  1. just cant fix 1996 175 hp
    By w,sajpel in forum Johnson Evinrude Outboard Forum
    Replies: 4
    Last Post: 04-21-2010, 05:54 PM
  2. 1996 115 hp v4
    By carlin_renshaw in forum Johnson Evinrude Outboard Forum
    Replies: 2
    Last Post: 03-13-2010, 12:52 AM
  3. 1996 6 hp
    By jetfixer in forum Johnson Evinrude Outboard Archive
    Replies: 2
    Last Post: 01-27-2009, 04:45 PM
  4. 1996 350 XL
    By utilityman in forum Crusader Marine Archive
    Replies: 4
    Last Post: 02-23-2007, 04:07 PM
  5. 1996 150 hp V6 hot
    By jwilliams in forum Johnson Evinrude Outboard Archive
    Replies: 3
    Last Post: 07-10-2006, 11:18 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •