Logo
FULL SITE MENU

Search results

  1. C

    87 Crusader 7.4L 350hp Spark Plugs Wire set ?

    Hi folks, Have to replace port engine spark plugs wires, on my 87, 7.4 Crusader 350hp. Is anyone has a Name Brand or part # that will be cut for it. I hate universal set. Henry G.
  2. C

    7.4 GSI 2000, Start and runs poerfect until you turn off, wont sart again until engine is cold?

    Have a 2000 7.4 GSI MFI. Cranks AND RUN GOOD UNTIL YOUR TURN ENGINE OFF. Crank but wont start within 6 to 12 hours after shutting off engine. Sparks OK, Fuel pumps running. Bad ECM ?????? Any help appreciated.
  3. C

    finding knock sensor on a 2000, 7.4 GSI V OLVO Inboard w/ 130hrs.

    Like to know where is the knock sensor located on this 7.4 GSI, 2000, Engine will only start after a 12 to 24hrs stop. Was told by a (tech ?) when by-passed it will start all the time. Also said It was not available anymore.. Is the module with fins part of this knock sensor?Your help will be...
  4. C

    1987 crusader 454 ac to ngk plugs

    Just bought NGK BPR6FS to repl Just bought NGK BPR6FS to replace my AC mr44t on both engines. Should I use same gaps? ( 0.035 in.) Mostly cruising @ : low RPM 1200 to 1500 Henry G.
  5. C

    Crusader 454 350hp Crossover pipe

    Is anyone knows if these cross Is anyone knows if these cross-over pipes are still available. Will hate to have to modify the complete exhaust system in my boat.
  6. C

    Flushing the UCOOLER 87 454 350hp

    "Hi guys, Need to flush the U "Hi guys, Need to flush the U-Cooler on my 454, 7.4 87 crusader port side engine, any suggestions how to do it? (muriatic acid?) Also is there an easy........way to remove the risers? do have crossover pipe on the exhaust sytem. Your advice always...
  7. C

    Ready to order my 1409 edelbrock carb cru 454

    Hi folks. I am ready to order Hi folks. I am ready to order a replacement edelbrock 1409 for my Crusader 454 1987 engine. I was told I need an adaptor to replace my Rochester Q-Jet carb. Do I need a different fuel line from the pump to carb. or is is the same fuel line (direct match). Will send...
  8. C

    1987 ChrisCraft 333 454 350 carburator specs

    "Have a pair of Quadrajet, Roc "Have a pair of Quadrajet, Rochester Carb. thinking about replacing with Edelbrock carb. Is anyone knows what CFM I need? was suggested 750 cfm, your expertise will be appreciated. Thanks Henry G"
  9. C

    Mercruiser wiring diagram

    "Hi folks, I know I'm on t "Hi folks, I know I'm on the wrong (BRAND) site, but it is for a friend, I need to find a site where I can get a wiring diagram (FREE IF POSSIBLE) for a 1986, 350, 5.7 V8, It's a Mercruiser engine. Henry G."
  10. C

    Wiring diagram mercruiser 1986 350

    "is anyone know a site to get "is anyone know a site to get the wiring diagram for Mercruiser 350, 1986. Need to know color code for wiring plug with pin # Thanks in advance"
  11. C

    Rear motor bolts on Merc 1986 57L Alpha1 drive

    "have one bolt out, the other "have one bolt out, the other one frozen salt solid, Bolt head gone, any suggestion how to remove bolt? Try PB Blast for a week, no result. Heat with propane torch, still not move. How about drilling? Any better ideas? Thanks Henry G"
  12. C

    Parts ID # to model ID #

    "Hi, Do have hundreds of new Q "Hi, Do have hundreds of new Quicksilver parts in original unopened packages. Cannot find where these parts fits OB or I/O models. Any site(s) in mind. Also have many NLA parts (new)in stock. I can go to Mercury/Mercruiser parts site and find prices but no...
  13. C

    ID description for MercuryMariner part #

    "Hi, Do have hundreds of new Q "Hi, Do have hundreds of new Quicksilver parts in original unopened packages. Cannot find where these parts fits OB models. Any site(s) in mind. Also have many NLA parts (new)in stock. I can go to Mercury/Mercruiser parts site and find prices but no references to...
  14. C

    Crusader 74L Rochester Carb Base Gasket

    Is anyone knows where I can ge Is anyone knows where I can get a pair of Carb. Base Gaskets for my Crusader model 350 (7.4L)I need 2 because of the 7 deg. riser plate. (straight shaft) Just rebuilt with an Echlin Carb. rebuilt Kit. Kind of easy to do.
  15. C

    CarterWeber carburator rebuilt kit

    "Is anyone knows where can I f "Is anyone knows where can I find a complete Carburator rebuilt kit for my Crusader, 7.4L model 350,( 4 BBL) Carburator looks like Carter/Weber Carb."
  16. C

    1987 Evinrude 15HP foammy liquid comming out exhaust stalls

    "My friend has a 1987 Evinrude "My friend has a 1987 Evinrude OB 15HP, Hard to start, spits foammy liquid from exhaust and motor stall and run rough at high rev but no idling? Compression is good, spark plugs looks clean. Fuel and oil mixes in tank? Any one has this problem before? Thanks in...
  17. C

    Wiring diagram for CC Amerosport 333 flybridge wtwin 454

    "Is anyone has or know where I "Is anyone has or know where I could find copies of the boat wiring's diagram. I do have the engine and gauges one, but the balance is missing. Just re-installing the Flybridge and cannot find where wire labels 23, 25 and 222 goes. Thanks Henry G."
  18. C

    Cleaning shafts and bronze props

    "Will like to know what work b "Will like to know what work best the clean shafts and props on my 87 Chris-Craft Amerosport. Just bought boat last December, Boat not used for 2 years. Can I sand or use steel brush on shaft? I am new to inboards."
Back
Top