Logo
FULL SITE MENU

Search results

  1. M

    water in boat

    seems i always get a bit of water inside my boat. its covered with a tarp and sits in the shade, somewhat is the water from considation? if it is, is there a considation , breathable top available?
  2. M

    Breathable boat cover ?

    iam replacing my floor in my flat bottom fiberglass boat. the boat's interior floor is gutted and for a cover i have a somewhat heavy duty poly gray tarp. i have been noticing a puddle of water, is this from condensation due to the tarp and the boat not "breathing" ? any boat covers that...
  3. M

    Navigator trolling motor setup

    i have a dual electric motor setup, Marinetech a total of 110 # thrust both motors are wired to one remote control .. only 1 motor turns any suggestions ? thanks ......
  4. M

    planing my boat

    i have a 9.9 evinrude on my 14 flatbottom fiberglass boat. my boat tends to lean more toward the stern when i have it on speed. if it makes any sense, i have the motor in its second notch from the clamp assembly .... tilting the motor out a notch, will it in essence plane the boat level ? i hope...
  5. M

    posting a pic

    someone please tell me how to post a pic on this site especially, the electric trolling link thanks
  6. M

    Charging issue

    TO ANSWER MY OWN PREVIOUS QUESTION ON THE TAPPING OF 12 VOLTS OFF MY NEW 24 VOLT STSTEM, I HAVE TO RE-ROUTE MY ACCESSORIES TO MY SEPARATE 12 VOLT BATTERY. I WILL HAVE 2-12 VOLT BATTERIES WIRED TO MAKE 24 VOLTS FOR MY NEW 24 VOLT TROLLING MOTOR I CURRENTLY HAVE AN ON BOARD CHARGER WITH 2 - 12...
  7. M

    custom rod builder

    want that ultimate fishing rod built ? i have been building custom rods for 31 years. i ship world wide .... HOOK, LINE & SINKER Rick Patton Emmaus, Pa. 18049 cell ....4846953933 [email protected]
  8. M

    fiberglass boat repair

    anyone looking to have any fiberglass boat repair .... i found that Maaco Auto repair, does excellent fiberglass repair work
  9. M

    24 volt wiring question

    currently, on my bass boat i have 2-12 volt batteries. one is for my gas outboard starting. the second 12 volt is for my trolling motor, depth finder livewell pump. iam going to replace my existing 12 volt trolling motor with a 24 volt system, using an extra 12 volt battery wired to produce 24...
  10. M

    prime transom live well pump

    is there a way that i can self prime my thru transom pump ? my livewell inlet is higher than my transom pump and at times it gets air locked my solution, currently is to remove the hose going into the sprayer and prime it with some water. anyone know how i can self prime it ? thanks
  11. M

    4 stroke gas question

    i have a evinrude 9.9 4 stroke outboard someone told me that regular gas octane will damage the injectors and that i should run a very high octane gasoline,or racing fuel. any truth to that ?
  12. M

    winterizing my outboard

    a first time gas outboard gas user and first time winterizing it i understand the fogger, and replace the lower unit fluid what about removing any water from the engine. do i worry about that ? or do i inject air into the water intake ?
  13. M

    non slip boat floor paint

    i redid my boat floor did not want to add carpet .... used Rustolem deck over paint 2X dries to a non skid very hard surface and available in many colors applied with a special "knobby" roller
  14. M

    steering wheel height

    converting my fiberglass boat to a bass boat i want to know if there is a "standard" height that the steering wheel should be from the floor? iam building my own console/ i realize the height of the seat has a lot to do with it also
  15. M

    2000 9.9 evinrude

    can anyone tell me the material used on my 2000 evinrude? i assume it's fiberglass. is it fiberglass layied over aluminum ? thanks
  16. M

    Bottom hull repair

    last year I had some issues with cracks in my fiberglass hull I searched and searched for a local fiberglass repair place, person I took this boat to my local Macco body shop yes, Macco and what a great job ...........
  17. M

    Evinrude 9.9 4-stroke

    last year I bought a 2000 Evinrude 9.9 4-stroke outboard. the motor came with a OMC remote control. is there a manual on how this control works I have never ran a boat with a remote control is there anywhere that I would find a model # thanks
  18. M

    remote control transom trolling motor

    i had plans to mount a engine mount trolling motor to my gas outboard. i dont have the required 13" from my cavitation plate to the water line to mount an engine mounted trolling motor. does anyone make a remote control transom mounted electric trolling motor ?
  19. M

    power tilt and trim ???????

    iam very new to adding a gas outbaord to my 14 ft. bassboat. i just added a evinrude 9.9 electric start can someone explain to me the advantage of adding a power tilt and trim. and if i even need one ? and what does that unit do thanks, rick
  20. M

    keeping my minnows alive

    to keep my minnows alive and fresh, i found a clear plastic food container. cut the height to fit inside my cooler. drilled a series of holes for water circulation. attached suction cups to the one side and attched it to the inside of my cooler. my minnows now separated by themselfes my cooler...
Back
Top