Logo
FULL SITE MENU

Search results

  1. H

    Honda outboards and others: managing salt crystal build-up in outboard cooling pathways

    20 minutes ,noted.
  2. H

    Honda outboards and others: managing salt crystal build-up in outboard cooling pathways

    I agree with the above. Fresh water flush as soon as possible minimum 10 minutes.
  3. H

    BF250D Spark plugs.

    Ok so I did my research. Both spark plugs have the same diameter , thread pitch and reach. The recommended ones have a 10ΚΩ resistor, the ones I got have a 5ΚΩ resistance which means the voltage /spark/will be higher. The only drawback would be possible radio frequency and noise, but apart from...
  4. H

    BF250D Spark plugs.

    I seem to have messed up with the spark plugs. Since I ordered some parts , I decided to go for the Iridium ones. Recommended for the 250D is ZFR6K-11E. Instead I got SPARK PLUG (IZFR6F11) (NGK). Will that be a problem?
  5. H

    Bf250 hard starting cold

    Yes Idle Air Control Valve. Remove clean and motor should start right up first time.
  6. H

    Flush Hose Attachment Point BF250D

    😁
  7. H

    2005 twin 225 Honda bf225 won’t go over 3400 rpm under load

    Yes, because if the boat will not behave in the xpected manner one’s mind goes to the engine. Many times the hull has growth and or the propeller has growth too which causes this situation.
  8. H

    BF175 cooling issue

    There is probably some foreign matter obstructing the water flow. Try some thick fishing line though the eater indication tube hole. Or maybe it’s time for a vinegar and/or acid rinse.
  9. H

    1999 130hp throttle & shifter cable replacement

    For my BF 130 year 1999 the shifter and throttle cables were Mariner (Mercury) cables.
  10. H

    Operating coolant temperature range for Honda BF225

    The D model is the latest model. They run hotter than the older model I believe.
  11. H

    Operating coolant temperature range for Honda BF225

    D model? if yes they run around 190-200F.
  12. H

    Newer Honda BF250 Question

    Like👍
  13. H

    Obvious Schematic Error.

    Ok so even the Original Shop manual may have errors… I think 18 and 19 valve been changed around…
  14. H

    BF130 water pump replacement

    If I remember correctly on my BF130 Year 1999, the impeller was rubber and the inner part was a whitish hard plastic sleeve. There were never metal parts on the impeller ant they were original parts.
  15. H

    BF 250D Exhaust manifold Inspection.

    Hi All, BF 250D about 2,1/2 years old not many hours due to Covid Pandemic restrictions. Engine services done properly with OEM parts and lubricants. I have been wanting to make a visual into the the exhaust manifolds just to get an idea on salt buildup or corrosion now that the engine is new...
  16. H

    BF250D trim tilt limit.

    Dear Honda Friends, is there a way to program the newer Honda BF250D to trim up to a specific point and no more? m Many thanks.
  17. H

    NMEA 2000 Relay Kit For Honda BF250D

    Dear Fellow boaters, Honda part 06332-ZZ3-000AH. Brand new Honda with lcd display. The Display for this boat is powered through the nmea 2000 network cable. The network cable has been connected to a toggle switch therefore I purchased the above relay so that when the engine ignition is turned...
  18. H

    Honda Bf130 Thermostat.

    Greetings fellow Honda owners. Bf 130 approx 850 hrs, 1999 model. I have followed the info about cracked heads and blocks. My Honda runs very well 20 years now. I ordered a new thermostat; I believe these engines had 80deg C thermostat and were replaced by 72 deg. thermostat , obviously to run a...
  19. H

    Bf130 Fuel pump trouble.

    1999 Bf130 without Vapour separator/electric pump upgrade about 840 hours. The usual 2 seconds fuel system pressurization cycle sounds mangled. The engine won’t fire up. I am sure it’s the electric pump which is at fault. Can someone please advise me: a)should I try disconnecting and checking...
  20. H

    Bf130 oil pressure light on green

    Dear fellow Honda owners, please help. Since reading the forum, I have come to realize that. The oil pressure light should: Go on for two sec. with the hight temp light together for 2 sec and then should go off. after engine start it should stay on (green) assuming all is well. In my case the...
Back
Top