Logo
FULL SITE MENU

Search results

  1. R

    2008 Honda fuel lines

    Greeting to all Has anyone ch Greeting to all Has anyone changed their old fuel lines over to protect from any problems with todays fuel? My boat is a 1999 and still has the original fuel line from the built in tank to the fuel filter. Wondering what I should change it with to make sure I...
  2. R

    1987 PCM 351 cutting out at 3800 rpmbs

    "Okay guys this one is driving "Okay guys this one is driving me crazy. Runs great up to 3800 rpm's, then starts cutting out and will eventually shut down. Have replaced carb, fuel pump, fuel lines, distributor cap, ignition has been switched to pertronix, coil has been switched to pertronix...
  3. R

    Holley 4160

    Does anyone have a good 4160 f Does anyone have a good 4160 for a Ford 351 or a good primary and secondary bowl that does not leak out the top plugs they want to get rid of. Please call me 704 361 3620 Tony. Thanks
  4. R

    1987 PCM 351 Holly 4150

    "Okay carb guys, my 351 was st "Okay carb guys, my 351 was starving when the secondary would kick in. Run fine up to 3700 rpm's. So I rebuilt the carb. I did forget to put the gasket on the power valve meter and have to go back in and do that. The first time I put it in the water, it ran up...
  5. R

    1987 Dixie 299 351 velvet drive drive line question

    "The large brass keeper nut th "The large brass keeper nut that screws over the brass unit where the shaft goes out the boat will not stay tight. If I tighten it down too much, it heats up. There is a stainless steel collar between it and the coupling plate on the tranny. There is only about...
  6. R

    2000 150hp Johnson Ocean Pro

    "Starts fine, but after 20 min "Starts fine, but after 20 minutes of driving, starts missing. Can bring throttle up or down and will start running correct for a short period of time. Runs at slow speed with no problem. Carbs have been adjusted and tune up performed. Any suggestions?"
  7. R

    1987 Dixie Sper skier drive shaft

    Greetings---There is a brass r Greetings---There is a brass retaining nut inside the boat where the driveshaft goes through the bottom of the boat. It loosens up when the boat is in gear and water comes in. Should I tighten it down with a wrench? Is there packing inside that to keep water...
  8. R

    1987 351 PCM Dixie Super Skier ignition problems

    Okay guys I bet this is basic Okay guys I bet this is basic but....I have no spark at the plugs and no voltage at the coil. Shouldn't I have 12 volts on the + side of the coil with the key in the on position. I can break the breaker points and get some spark on it but not much. Does the...
  9. R

    My first PCM Need advice

    "Greetings--Just bought my fir "Greetings--Just bought my first inboard w/PCM 351. 1987 Dixie Super Skier. Are there any benefits to replacing ignition with solid state componets? It still has points/condensor style? Can I use automotive parts on it (fuel pump, starter, hoses, etc) or do I...
  10. R

    150 Johnson Ocean Pro 2000 year model power pack

    Can the power pack cause probl Can the power pack cause problems in mid range rpm's? Mine runs great at low and high rpms. 3000 to 4000 rpms after it has warmed up cuts in and out.
  11. R

    2000 Johnson 150 Ocean Pro cutting out

    "Greetings, my 150 will run go "Greetings, my 150 will run good at idle and 4000 rpm's. If I bring it down to 3500 it starts cutting out and will die. This is the only rpm I have a problem with. 3000 or 4000 it runs good. Got manuals, any suggestions."
Back
Top