Logo
FULL SITE MENU

Search results

  1. P

    Ignition switch Wiring Orientation

    I have a 97 200hp Evinrude E200TXEUA. Recently the forum helped me with a kill switch problem. I ordered a new one and installed. I replaced the wires one at a time. I feel I done that correctly. The engine cranks and runs well. The problem is, the kill switch still does not kill the engine...
  2. P

    kill switch not killing engine

    I tried to search for specific info, but did not see what I needed. Returning to our boat basin, some how iI pulled the kill switch lanyard, and the engine did not die. The key pushed out like it should, but the engine kept running as nothing happened. So, I reinserted the clip and motored...
  3. P

    Install gear case on 97 200 Evinrude

    Am confused on this. When I removed the gear case, the factory manual said to place the gear case in reverse. Replaced the water pump, etc., and reading the manual to install the gear case it said to place it in forward. Correct me if I am wrong, but that would make the shift rod in the "up"...
  4. P

    97 fastrac t/t problem

    Gentlemen, My old fastrac reqiured big dollars to repair, so I got another off ebay. My problem is: The trim cylinders will not retract all the way in. Both stop halfway like its bottoming out. The tilt cylinder seems to work right. I have went through the bleed sequence around 25 cycles...
  5. P

    fastrac t/t disassembly

    Gentlemen, My 97 200 t/t will not stay down in reverse, otherwise it works good. Will a new seal/oring kit fix it?? I have the unit off the boat, and drained. In order to remove the bolts for the resovoir, pump assembly, and cylinder caps: will it hurt the unit or me (explosion) if I apply...
  6. P

    200 rearing up in reverse

    My 200 has the fastrac t/t system. Generally it works well, the fluid level is full, but when I get on it hard in reverse the engine comes up, but not out of the water. What is going on??? Any ideas? Does not lock in place, Thanks.
  7. P

    adjusting the cam pickup point, 1997 200hp oceanpro

    I have not posted in a while, so I hope some of the old pro's are still monitoring the site!!! On my 1997 200 oceanpro, I need to adjust the cam pickup point. The manual calls for a gap of .005" between the roller and cam. Mine has no gap. My question is, in order to make this adjustment, must...
  8. P

    Primer solinoid

    "My question is, "can a le "My question is, "can a leaky primer solinoid affect idle speed and smoothness ?" If I understand how this little gizmo works--enriches the mixture when the key is pushed in, or the override handle is turned up, and the fuel pump pushes fuel into the intake. I have...
  9. P

    Used volvo parts

    "I have good used 140 parts--- "I have good used 140 parts---block, starters, carbs, outdrives etc. I am out of the volvo sterndrive user world. If someone needs good parts I have some. Thanks."
  10. P

    Console mounted kill switch 97 200 texua

    "Gentlemen, I have used the se "Gentlemen, I have used the search feature to try to find an answer to my question, but did not get what I need, so here goes. I replaced my kill switch, but it still does the same thing, so I am not sure if it is normal or not. As I trailered the boat...
  11. P

    Headgasket replacement

    "My motor is a '97 200 loo "My motor is a '97 200 looper. A couple of weeks ago I was talking to a local mechanic, and he suggested I need to replace my headgaskets this winter as a p.m. in order to "head" off any problems with future possible water leaks into my cylinders, due to the age of...
  12. P

    Appreciate the help

    "Recently I posted on the foru "Recently I posted on the forum for help locating a shift interrupt switch for my 97 looper. JWBMarine gave me the part number in no time! I have installed the switch, and unless it is my imagination, the engine cranks much much better, cold and hot,idles...
  13. P

    Shift interrupt switch

    "I have tried to locate a shif "I have tried to locate a shift interupt switch for my 97 e200txeua, serial g04319767. I have looked on evinrude.com. joe reeves store, maxrules.com, and the sites store. Can someone point me in the right direction so I can get on ordered asap. Thanks!!!!!!!!"
  14. P

    Questions on oil and water pressure gauge

    "This is my first big o/b, a 2 "This is my first big o/b, a 200 looper on a 22' hydra sports. I am somewhat confused on marine two cycle oils, and prefernces may enter here, but....... Prices vary from nine dollars to 36 for name brand synthetic two stroke oils. I do not mind paying for a...
  15. P

    Carb concerns

    "I have a 97'200hp evinrud "I have a 97'200hp evinrude, which I have had a little over a year. The engine runs well wot and mid range. It cranks and generally idles well. But, my concern is after throttling back after cruising, the engine seems to want to "shake" somewhat. Since buying the...
  16. P

    200 ocean pro prop shaft

    "I want to try a different pro "I want to try a different prop on my 97 200 o/pro. It has a 15 spline shaft, I do not know the o.d. Would a prop off an 89 200 fit? Thanks for a reply!!!!!!!!!"
  17. P

    Throttle linkage rollerzincs

    "Recently I posted about clear "Recently I posted about clearance issues with my throttle linkage roller and the clearance between it and the spark advance cam. No one felt comfortable to offer a follow up. After reviewing a parts diaghram of the throttle linkage, I noticed a replaceable...
  18. P

    Throttle cam follower clearance

    "I have recently bought a 97 2 "I have recently bought a 97 200hp carb evinrude. I have been tinkering with the motor and it runs good. My Seloc manual says the throttle roller clearance from the timing advance cam should be set at .005" clearance. There is close to .040" as is. I bought a...
  19. P

    97 power tilt trim motor replacement

    "The fastrac power trim and ti "The fastrac power trim and tilt motor on my 97 200 rude carbed motor needs replacement soon. It works good, but the motor housing is very rusty and am afraid it will start leaking soon. I ordered one from the site, so I will have it in a couple of days. My...
  20. P

    Vro2 oil sensor

    "I do not have a problem, but "I do not have a problem, but want to know how my 200 carbed motor detects when there is no oil being supplied to the fuel mixture? I do realize the oil tank will sound low oil when the tank is 1/4 full. Thanks for the info in advance."
Back
Top