Logo
FULL SITE MENU

Search results

  1. B

    Jw14 won't run with air intake tube attached

    After putting thread on one fuel needle I tested it without the air intake tube on and it ran great. There was exhaust coming out of the rear intake screws so the tube was put back on. It starts runs a few seconds and quits. Maybe the tube is plugged up? Thanks
  2. B

    JW-14 fuel needle packing substifute

    Will an boring or something else work? Thanks
  3. B

    Can the metal hub on a 1985 8hp prop spin out?

    I can try marking it to see for sure E8rcob Can zI replace it myself? Thanks
  4. B

    Flywheel torque for 4 cyl 2002 merc

    Don't know what the hp is and this the only info on the motor: 3m9xm01131co Fel158-7 Sept 2002 Mercury 4 cylinder Thanks
  5. B

    Need motor ID

    3m9xm01131co Fel158-7 Sept 2002 Mercury 4 cylinder Thank you.
  6. B

    Need help assembling turbo 35

    Should have take a picture first. Oh well Thanks
  7. B

    What does a 2002 merc power pack look like?

    It's a 4 cyl motor. That's the only ID I have right now. Thanks
  8. B

    Endurance c-2-55 power source

    First it is model 1352256 L362mk00645 C-2-55 Got this motor off a junk pile and applied power to the 2 tabs and both forward and reverse worked. Had to stop due to the light wires getting too hot. Looks like it uses a plug in cable but I can't explain how power gets to the tabs. Can someone...
  9. B

    2003 M8b turns boat hard right

    It is on a 14 ft alum boat and there isn't any trim tab or adjustment that I can see. The manual doesn't have any suggestions. What can be done about it? Thank you
  10. B

    Evinrude I'd for parts

    My friend has a 9.9 Evinrude that uses condensors and points. The ID is gone. According to Lee's Ramblings these were made between 74 and 76. I looked at several different model numbers and they all use a water pump kit #0394711 or 18-3327 which it needs. I wanted to check and see if all these...
  11. B

    8rcob 1985 8 hp electrical problem

    When trying to start it backfires through the exhaust and is almost impossible to start. It i is difficult to fire with with carb cleaner. It will buck up and down some, smooth out ok then quit, not in that order. The compression test was about 135. The flywheel key is like new. It has new...
  12. B

    Need single leaf spring for Dilly trailer

    Nobody seems to carry a single leaf spring for a model M-14-15 1974 trailer. It is 30 3/34 inches long and 1 3/4" wide. Any suggestions? The stud it sits on may not be long enough for a two spring. Thankyou.
  13. B

    Honda 2hp piston not working

    Model bzbf1401322 There was a snap and the motor died. The piston doesn't move when turning the flywheel or prop. It isn't froze. What do you think it could be? If I take the top plate off can I see the rod? Thanks Bob
  14. B

    Pontoon deck, fiberglass covered pressure treated plywood?

    I have the fiberglass and was thinking I could cover the bottom and edges with glass instead of using marine plywood. Will it work?
  15. B

    86 30hp shift arm cable pin replacement

    When attempting to take the shift cable off the motor, the end of the pin broke off. How do you get a hold of the cap lock nut behind the shift handle? Is there a sub for a new pin that can be made? Thanks
  16. B

    8Ercob jumps around above idle

    Motor knocks worse as more power is applied. Sometimes it will smooth out , go fast, then quit. I took the lower unit off and spun the flywheel with a drill and there wasn't any knocking. There weren't any metal filings in the lower unit and the prop turns smoothly. I am positive it wasn't water...
  17. B

    1985 E8rcob carb not getting gas, take welch plug off?

    I put in carb cleaner for 3 days and used a wire in holes . Ran ok once for 20 minutes, now it won't start because the plugs aren't getting fuel. I have cleaned it several times. I didn't put in a new welch plug and was wondering if there could be a problem in that area.
  18. B

    E8rcob backfires water when trying to start it

    I put a new carb kit in with the plastic float. It will start sometimes and go like it should but it might quit and take an hour of adjustments to go again. Right now it blows water out of the barrel when trying to start it. I richen the mixture but it doesn't help. It is critical about what...
  19. B

    8rcob 8hp 1985 starter spring

    Is there supposed to be a 90 degree stud on the bottom of the spring to catch in the base plate slot? Thank you.
  20. B

    Farnas davit switch only runs one direction

    Hi I have 2 farnas switches. One was wired the same way as the other but won't turn on in one direction. The switch looks new. Here is how they were wired Power side L1 blk L2 white Motor. blk 1. Red 2. Orange 3 white 4 Green tThanks It isn't a drum switch. Any suggestions? Thanks.
Back
Top