Logo
FULL SITE MENU

Search results

  1. M

    Honda 100

    "Had to put puller on the prop "Had to put puller on the prop to get it off. The shear pin was wedged. I noticed the the prop shaft shear pin hole is egg shaped. How big of job is it to replace shaft? Any ideas on where to order parts? Thanks, Bill"
  2. M

    Spark plug gap

    1990 305 chevy 4b carb... w 1990 305 chevy 4b carb... what should I set the gap at? Bill
  3. M

    New yamaha 350

    I am thinking of putting one o I am thinking of putting one of these on my boat . Just was wondering if they are as good as salesman.... was hoping for quiet and slow troll out of it ...power I'm sure I will be impressed.. Fresh water Bill
  4. M

    Prop pitch

    My buddy has a boat with 6 dif My buddy has a boat with 6 different props. help 1995 240 thompson fisherman 24 ft. lenth 305 merc. stern drive 4500lbs. est. What prop should he run? boat will not plane out at 3800rpms.
  5. M

    Back fire thru the carb

    "I was running to the launch y "I was running to the launch yesterday aboat 3800rpms and 3 quick pops came out the carb and lost power ... I throttled down and it shut off .... sat there aboat 2 min. scratching my head and decided to start it up.... it ran good the rest of the way in...
  6. M

    Shounds like u jount

    "Been fishing and at slow idle "Been fishing and at slow idle and when I am turning the wheel I here a slight rapping noise. Very faint but still a new noise. I just put new gimble in, and u joints were perfect. Must be engine coupler when I speed up it goes away. It's not the motor...
  7. M

    Shift shaft

    I noticed my shift shaft has a I noticed my shift shaft has about 3/8"-1/2" up and down play in it... Is that OK or should I be replacing more parts?
  8. M

    Soft plug

    Can't find a soft plug for Can't find a soft plug for my upper half of my outdrive............. alfa one ............. keep getting discontinued part from everyone....
  9. M

    Gimble bearing greasing

    "I was all ready to re-assembl "I was all ready to re-assemble my lower unit and thought it would be a good idea to grease my new gimble first. So I put 5 pumps in & reached in and turned the bearing a quarter turn put 5 more pumps in and so on. The last time I reached in I pulled out a...
  10. M

    Fuel line

    "Was wondering where to splice "Was wondering where to splice into my fuel line to run my 4 stroke kicker motor or is this not a good idea? I like the idea, it would save time & wouldn't have to refill the 3 gallon tank, save space on the boat.... but I can see issues that might arise like...
  11. M

    Throttle

    I have 9.9 honda 4 stroke I us I have 9.9 honda 4 stroke I use as a kicker for trolling... Would like to convert throttle so I can adjust my speed while trolling.(From inside of the boat) Also hoping to make the adjusting of the throttle not so sensitive.. All advise is wecome THX...
  12. M

    Electric Trolling Motor Transom Mount

    Was wondering if anybody has m Was wondering if anybody has mounted a trolling motor on the alfa one transom? Does it mount OK and operate like Advertise Found 1 person that said it would not mount to a older merc. 1975 model. Minn kota 202 was the trolling motor. All advise is welcome.
  13. M

    Exhaust flapper

    "I just replaced my gimble sea "I just replaced my gimble seal,bearing,all bellows,water hose,trim switchs and started on water pump... I looked in upper half of out drive and there was a exhaust flapper just laying there... It looks worn out but my real question is where the heck does it...
  14. M

    Bearingssealsbrakesect

    "Hi, Just took my wheels of m "Hi, Just took my wheels of my trailer to replace the rubber and ##@@!%&!!!. I need the wheel cylinder,push rod that goes in it and the rear seal. Where is a good site that has better parts break down & disciption? Any help is appreciated"
  15. M

    Trim senser

    Both of my trim sensers have b Both of my trim sensers have bad wires They are located over top the hinge pin bolt. Is this a merc. part ? thx Bill
  16. M

    Bellows greasesealant

    What are you guys using? Ha What are you guys using? Having trouble finding this also. Bill
  17. M

    Hinge pin tool

    Looking for hinge pin tool Looking for hinge pin tool looks like a star drive but not sure napa can not get it help Bill
  18. M

    Sevice kit transon

    "I,m a little confused there a "I,m a little confused there are 2 service kits for my 1990 5.0LX V8 Alpha one. My serial #s are:engine OD377815,transon OD347647,and drive OD353629. One kit is for a straight exhaust bellow with a exhaust tube in it. The other kit is for a exhaust bellow with...
  19. M

    1990 mercruser 305 chevy

    "Hello, I'm A new boat ow "Hello, I'm A new boat owner. I had my boat winterized by A professional last fall and all fluids changed. He told me my gimble is siezed up,my bellows shold make it another year and my throtle cable border line. So I figured out what B.O.A.T really stands for;Bring...
Back
Top