Logo
FULL SITE MENU

Search results

  1. hystat

    Omc 800 mechanical lower

    I'm finally getting out of the OMC stuff. Parting out my last boat. Watch my ebay account for more stuff like this: www.ebay.com/itm/131518114402 I'm still gonna hang out here and try to answer questions. I have a lot of selectrim (V6) stuff and tons of OMC bits I'll be clearing out.
  2. hystat

    growly SE116 gen ii

    I put a 116 upper on my Gen II V6 1.8? ratio last fall before storing the boat and noticed a bit of a growl, more pronounced after a longish run. Seems to almost disappear in neutral, noticeable at idle in gear and at slow plane. ran it about 15 hours thinking it might just need breaking in...
  3. hystat

    Volvo AQ165 Engine help

    it is 1 piece
  4. hystat

    bad oil pump? that's my guess AQ130C failure analysis

    A few years ago, I traded about $50 worth of OMC parts for an AQ130C engine at a marine outdrive rebuild place. The guy knew nothing about the motor. he had collected the engine with an outdrive. I just recently got around to looking at it (had the starter off my 131's B18 anyhow, so thought...
  5. hystat

    Coil, voltage reg or Alternator

    I prefer one battery + 1 of these on board.
  6. hystat

    this person needs our help...

    http://ontario.kijiji.ca/c-cars-vehicles-boats-watercraft-powerboats-motorboats-Long-shLong-shaft-boat-motoLong-shaft-boat-motorotor-W0QQAdIdZ269704002 Wanted: Long shLong shaft boat motoLong shaft boat motorotor ong shLonong shLong shaft boat motoLong shaft boat motorotorong shLong shaft...
  7. hystat

    '68 sea ray w/ 78 chevy 305 electric shift intermediate housing issue

    all the intermediates seem to have a big access cover inside the boat with access to that bearing area - guess you could fill it there. #16 in the pic 16 0313247 COVER, Oil reservoir...
  8. hystat

    GLM0411 26T Gear? V6 FWD gear maybe?

    In a box of parts I bought on eBay years ago is a new GLM0411 gear. 26T looks like a V6 fwd gear. just want to inventory it.... or toss it... I don't see any reference to 411 in any GLM catalogs. Anyone recognize that number?
  9. hystat

    New project. Ideals anyone

    better idea - dealer near me has a NOS 2005 4.3 MPI for a nice price....droool:
  10. hystat

    1977 351w with a stringer outdrive... wanting to pressure check it,if possible

    what he said - put 5 or 10 psi in where the green arrow is. block hoses at red x's:
  11. hystat

    engine change from mercruiser 120 to 4.3 liter - need help on exhaust change fix

    I f the 4.3 is same vintage as the 120 coming out - you just unbolt the single, and bolt in the Y pipe. there's no fix needed. the 120 might have the manifold on the left side, but the exhaust doesn't exit the boat on the left - it exits dead center as it does on all mercruisers If you don't...
  12. hystat

    1985 Crew 3.8 litre 229 cu in Chev. / 800 Stringer

    might want to check the anti-siphon fuel fitting at the tank connection. there's a ball and spring inside and it doesn't take much to jam it up. Like a piece of red plastic from a jerry can:
  13. hystat

    International Harvester 9.0L marine DV-550 DV-550B

    I have a pair of new exhaust manifolds for one...trying to figure out what years and if anyone besides PCM marinised these
  14. hystat

    Using Dry Joint 2008 4.3 L Manifolds on a "Cold Manifold" system

    I have 2008 4.3 Dry Joint manifolds on my 1985 MR185 (229 V6 Chevrolet) I had to use the old cold manifold style thermostat housing (has to do with alternator mounting) so I a plugged the riser feed port and have just 1 hose to each manifold feeding the bottom. I see my temp gauge climbing...
  15. hystat

    10 years too late invention

    was just thinking how easy it would be to make an outboard bracket that mounts on a stringer intermediate. I'm no designer..haha... just a bad idea guy cast aluminum dowel that bolts in the trunnions (A), then sits in the dowels below the exhaust holes (B), then a couple of transom pads to make...
  16. hystat

    1973 Johnson 25hp acting like prop hub spun...

    but it hasn't spun. I tried several props. It does it the worst with the 12P. almost held on plane with a 10P, but then slipped. If the dogs in the lower were gone, I would expect clunking. But this feels exactly like a spun prop hub. Holds torque until just about to plane then revs up...
  17. hystat

    AQ280 DP drives... who was looking for 2.31?

    someone was posting here a while ago and contacted me regarding these 2.31 ratio 280's please PM me if still looking - thanks
  18. hystat

    Need a tiller for 1990 40HP

    "looking for the complete till "looking for the complete tiller with shifter and cables to convert a 1990 40HP. the BRP conversion kits seem to start about 1995... so 1990 requires all the itsy bitsy pieces to be bought through parts... So, I'm looking for a decent used one - thanks...
  19. hystat

    Duoprop ratios 195 vs 23

    "Does anyone have a listing of "Does anyone have a listing of what packages used the two different DP ratios on the AQ series drives? I picked up a 2.3 ratio DP lower for my AQ180, but now I'm thinking the 1.95 would be more correct for all V8's even though my 180hp V8 is more like a V6 in...
  20. hystat

    Help IDing Duoprop Proset 280 Diesel

    From a280 drive - was behind a From a280 drive - was behind a diesel. The rear prop is 4 blade so I guess that makes it A series. Only legible numbers are M24431 R5795 (4 blade) M18274 R5793 (3 blade) trying to find out what set they are
Back
Top