Logo
FULL SITE MENU

Search results

  1. G

    Tamd40 parts for sale

    Got divorced, sold the boat, but I have an engine to part out. My business is repair, so I am going through some of the parts. Also, if you have any parts that need repair, please contact me @ 225-278-9683. I will post parts on eBay also. Check me out on Facebook. Adolph Mechanical Service.
  2. G

    Tamd 40 parts for sale

    I have sold my boat, by I still have a few spare parts. I replaces an engine and have a nice head, water pump, oil cooler, heat exchanger, crank, cam etc. The water tank can be repaired also. I can repair it if you are intrested.
  3. G

    TMD 40 Parts for sale

    Tank needs some work, but I can fix it and test it.
  4. G

    TMD 40 Parts for sale

    Had to shrink pictures to up load. Why computer nerds say that instead of "Error 413, bubbles to wysiwuget"?
  5. G

    TMD 40 Parts for sale

    Turbine housing
  6. G

    TMD 40 Parts for sale

    Here is the insert that I have for sale. Is this what you need? I also have a tank, but it needs minor repair. As far as a turbo, I delt with Doug at Acadiana Diesel. http://www.acadianadiesel.com/ 337-365-2887 He ordered a new cartridge for mine. Depending on the condition it is in, you may be...
  7. G

    TMD 40 Parts for sale

    Does $200 plus shipping sound reasonable?
  8. G

    New method to remove heat exchanger bundle

    Here are so photos of the bundle I removed from a tank today. First, cut down the side of the tank with a cutoff wheel to free the bundle. Next place 2 2x4's in the rear of the bundle and use the whole setup as a pile driver. The slit I made can easily be repaired by an aluminum welder.
  9. G

    TMD 40 Parts for sale

    I bought a used engine online and I have a few parts extra to sell. TMD intake manifold, Injector pump, oil cooler and maybe a head. Please let me know if you are intrested.
  10. G

    Port Engine problems

    I took my boat out for a shake down today. The port TAMD 40 oil pressure slowly dropped until the blowby started blowing heavy smoke. The question is "After I pull the engine, would it be sufficient to replace the main bearings, rod bearings and seals? or should I plan on replacing pistons and...
  11. G

    Coolant filter install

    I am considering a coolant filter install on the coolant side of my TAMD40ab. Here is a link to a good website describing the coolant filter. http://www.dieselwarden.net/ford/coolfilter1.html My question is has anyone installed one on a TAMD engine? Where is a good place to plumb it? High...
  12. G

    TAMD 40 oil pressure drops

    My port engine runs a short while and the oil pressure drops to zero. No noise or tapping. I ran with a manual gauge with the same results. I pulled the oil cooler and checked the bypasses. Everything looks fine. Before I pull the engine, is there anything else that I am overlooking? Can I...
  13. G

    TAMD40 Oil pressure drops, will not idle.

    I was running my boat when I noticed the oil pressure drop to near zero. I pulled the throttle back and the engine died. After it cooled off, It started and ran fine. 10 to 15 minutes later oil pressure dropped again. Pulled throttle back and stalled. No knocking or overheating. Is there...
  14. G

    Overheating 1977 Volvo TMD40 Turbo Diesel w/280 Outdrive

    Had a similar problem on My Tamd 40. Was the bundle for the heat exchanger pulled and cleaned? The shell side or tank with the fresh water was dirty.
  15. G

    Need Parts! Insert 858833 backordered at Volvo.

    I am searching for the insert (PN: 858833) for my TAMD 40a. It is backordered at Volvo. I think the mine in Sweeden is on strike! Anyhow, if someone has one lying around, I sure could use it. Snapper season is here!
  16. G

    TAMD40 overheating problem found.

    I finally was able to remove the insert from the housing after cleaning the system several times with various cleaners.I still had solid paste like stuff on the bundle. I had to use a 20 ton shop press and I broke the bundle getting it out. The housing has a lot of corrosion. The price you pay...
  17. G

    Wagner A W helm Seal Kit

    Does anyone know where I can obtain a seal kit for my Wagner A W helm pump? The net was not very kind in my search.
  18. G

    Parts Help

    I am in search of the "Dog bone" that drives the sea water pump on my TAMD 40. It is not listed with the sea water pump, nor the gear cover. It is a small metal piece with rubber ends. I'll look again, but a Part number would be helpful. Glen
  19. G

    Aftermarket thermostats

    Does anyone know the part numbers for an aftermarket thermostat for a TAMD 40b? It would save me some money if I could order some from the local parts house instead of mailorder from VP. Thanks in advance!
  20. G

    Looking for used part for MS3 reverse gear

    Would anyone in the US have a connection pipe, VP #851730 they are willing to part with? I think mine froze and broke. I will try to repair. Volvo wants $340 for a new one. Thanks!
Back
Top