Logo
FULL SITE MENU

Search results

  1. P

    Leaking Fuel From Air Intake Gasket

    Typically I see fuel leaking from the gasket seal (#10) when I have he engine tilted up. Not a lot but some. I think the intake cover and gasket is supposed to collect any excess fuel item (41 and 28 along with gasket). Any tips on making this a better seal? A couple of the bottom screws are...
  2. P

    9.9 1974 Johnson Heavy Black On Plug

    10R74S 9.9. ……could be a long one Rebuilt carb 6 weeks ago with OEM kit started well and ran in barrel. Adjusted lean/rich mixture at the time and no issues in barrel. Have not run it on water until this weekend. Went out trolling and started the 9.9 rather then run my 70hp. The 9.9 seemed to...
  3. P

    70 HP Trim Seal Kit 393942

    Bought the above OEM seal kit for my J70TLCNB 1982 Motor and it’s not clear what is supposed to be in the kit. I can see on the parts diagram item 33 which is 0321716 some type of ring(backup) but it does not look to be part of the kit I purchased and it was not on the trim assembly when I...
  4. P

    Showa or Prestolite Tilt

    Is there a way to tell what tilt cylinder I have? Motor is J70TLCNB and pic of tilt trim assembly I am looking to change out seals due to leak and I read that the cylinder could be Showa or Prestolite. Maybe I am wrong but I thought I would check TIA
  5. P

    10R74S 9.9 Johnson 1974 Spark Plug L82C or L86C

    The parts breakout lists the 2 spark plugs. Does this indicate both are acceptable? I use this motor as a backup and for trolling. I have searched the forum and websites but no clear answer. Which is the right or preferred one? Thanks!
  6. P

    1982 70HP Johnson J70TLCNB Tach and Controls

    Couple of questions concerning the controls and adding a tach. The pic of the controls show a knob labeled Throttle/Friction/Accelerateur...what does this actually do? The harness below has a purple wire I believe is sending information to my trim Guage. There appears to be two empty ports on...
  7. P

    1982 70HP Johnson -Carb blocked

    Motor runs great until it bogs down trying to get to higher speed. Speculated it’s debris in carb somewhere so took a look at carb drain and idle jets. Found blockage in bottom one, cleaned and put back together. Ran great. Same thing a happened a few days later. New fuel filter on engine and...
  8. P

    70HP 1982 Johnson Outboard and 9.9 1974 Johnson Outboard on 1981 16ft Sylvan Alum Boat

    Just a general question on the above 2 motors and boat combination. Any special issues to watch for? Parts readily available for both? Is the Sylvan Aluminum boat decent? Any known leaking issues on the Sylvan? Just looking for any feedback or opinions on any of this! Thanks! 70HP 1982...
  9. P

    Any Idea on AGE/Model for Chrysler Boat and/or Motor 70HP

    Attached pics of a boat and motor that I am looking for any guidance on. Sorry I have no other info on either..... Boat is 19ft and motor is 70HP Age? Model? Any major flaws to watch out for on either? Is this motor worth touching? Is the 70HP ok for a boat this size? Thanks.
  10. P

    Model 2004 SN 1252 1969 Chrysler

    I think I have a problem……still working on 15HP Chrysler and I went and bought a 20HP one…… learning a lot on the 15 so what the heck. Cost was 40$ cdn. Things I know: Great compression and the guy said there was only spark on one cylinder. Could not check the state of the lower end oil since I...
  11. P

    15HP 152BA Reverse Gear Linkage

    With the cover on I can not shift into reverse. I don't want to force it into reverse but If I take the cover off I can manually push the back lever (below fuel pump) to reverse with no issues. Not using a lot of force to do this either. Neutral and Forward are fine but seems to be a lot of...
  12. P

    15HP 152BA Woodruff Key

    The woodruff key sheared but I can not find the part number for this. Can anyone assist? I think it's 1/8" x 3/4". Thanks!
  13. P

    15HP 152BA Adjusting and Running

    Hey! Looking to tune in my new to me Chrysler Outboard! To get here see below and via a couple other posts: Partially rebuilt carb along with many cleanings Changed out fuel pump diaphragm Changed fuel lines on motor and tank Changed O rings on fuel fittings Changed the starter gear-broke last...
  14. P

    15 HP 152BA Fuel Flow Issue

    Did not find much info here or in my wider searches for info on this so I thought I would make a thread for it. The motor seems to be running very smooth after going through a number of updates -Thanks Jerryjerry05- I still have the problem of leaking fuel from the quick connect fitting at the...
  15. P

    15 HP Chrysler 155BA

    New member and New to me Chrysler outboard. I think its a 1974 but info is not always clear. Have not been able to get it running yet. Compression was good but no spark. I was able to get this corrected by checking condensers and cleaning the points as well as gapping one of the points. Have...
Back
Top