Logo
FULL SITE MENU

Search results

  1. C

    1978 lm318 manifold riser gaskets

    I have fresh water cooled engines with raw water cooled manifolds, risers, and elbows. I recently pulled all my elbows and risers to clean them out and re gasket them. I was somewhat surprised to find that the gaskets only had the round hole at the top open, and the 2 side and 1 bottom holes of...
  2. C

    Lm 318 dropping cylinder

    Looking for some input. I have twin lm318's and my port engine has been dropping and picking up a cylinder at idle. Plugs, wires and cap are new. I have done multiple compression tests and some times it comes up good, other times, low. At higher rpm this engine lags behind the starboard engine...
  3. C

    need upper gearcase

    I need a used upper gearcase to fit a 1985 800 series w/5.0 ltr engine. If any one has one around, or knows where one might be for a reasonable price, I would appreciate the help.
  4. C

    1970 350 commander distributors

    I am trying to source out new distributors for a 1970 CC 350 Commander with twin 350 motors. They must have the tach drives and the flat top caps to stay original. Does any one know where to purchase new ones?
  5. C

    2005 15 hp bigfoot carrier bearing torque?

    Does any one happen to know what the torque spec is for a 2005 15HP Bigfoot propshaft carrier bearing? I do not have the manual for this one, and I have not been able to stumble upon the specs online. Any help would be greatly appreciated.
  6. C

    Where to get distributor springs?

    My marine parts supplier and local auto parts stores seem to look at me with a blank stare when I ask about new springs. Can the be bought seperately, or just springs and weights, and where?
  7. C

    2007 305 valve setting

    I am working on a 2007 305cid m/c mpi. The boat has 54hrs on it and was sunk. Engine has been completely rebuilt due to internal rust pitting, and was test run on muffs. With throttle only engine will take revs, but in the water under load I have to baby it up to 1600rpm and then it will cough...
  8. C

    1998 Evinrude 70HP 4 stroke poss IAC valve failure

    "This engine is low hrs and in "This engine is low hrs and in meticulous mechanical condition. Suddenly it began having cold start issues. Turn the key and it fires instantly and runs 10 sec. then quits. Runs 10 sec. then quits. etc. If I play with cold start lever, I can make it run at 2000rpm...
  9. C

    1985 DT115 parts needed

    "I have just rebuilt a dt115 t "I have just rebuilt a dt115 that has been apart for two years, and upon reasembly I realized that I have lost/misplaced the oil injection tank and the aluminium front cover plate for the carbs. If anyone has these parts for sale or knows where to aquire them, it...
  10. C

    Merc 6hp water in cylinders

    "we have a merc 6 at the shop "we have a merc 6 at the shop that has very few hours on it and is creating water/oil sludge in the cylinders, the exhaust manifold, and the ports. The power head has been removed, the gaskets replaced, and the crank seal is clean and not milky. We are at a loss as...
  11. C

    Alternator rotation

    "Does anyone know what accesso "Does anyone know what accessory parts are different for a reverse rotation engine? Is the alternator, fuel pump, and raw water pump specific, or are there easy changes that can be made to make them function on either engine?"
  12. C

    Paragon planetary gears

    "I have one of my pv33 transmi "I have one of my pv33 transmissions torn down for a rebuild, and was forced to take apart the planetary set. I am curious if anyone has any tricks for re-assembling the two hundred or so needle bearings that fall out of them...Chris"
  13. C

    Paragon pv33r assembly and parts

    "I am new to the site and alre "I am new to the site and already added this to the end of an old discussion, so I will try a new one. sorry. After a series of stupid mistakes on reassembly of my boat after shipping accross the country, the end result was one blown up paragon tranny. I purchased...
Back
Top