Logo
FULL SITE MENU

Search results

  1. C

    can anyone get me a parts diagram for this remote?

    this boat needs a new trim switch and i can't find any info on it. anyone have a model # or an actual diagram would be great
  2. C

    25hp force outboard needs fuel pump,--NLA

    so i cant find this pump, it comes up as not available on all the sites. even ebay cant locate it, anyone have an idea as an alternative. #1 819213 1 PUMP ASSEMBLY-FUEL (1 required per assembly) 819213 1 - PUMP ASSY-FUEL,NLA [ More info ] Unavailable #2 27-820748A 1...
  3. C

    how do you determine how long the skeg should be when the old one is broken off?

    i have a customer with a 2021 yamaha VF 250XA vmax 250SHO and the skeg is broken. i have a shop to wel the new one on but how long shold it be? what is hte bottom width>?
  4. C

    loss of power over 3500 issue resolved and worth keeping in mind

    i have come across this issue about 4 times this summer and wanted to post it here in case others are experiencing this issue. boats would run great at idle and under load but when you climb over 3500 the engine would bogg down and stall. and may keep running if you pull back on the throttle...
  5. C

    loss of power over 3500 RPMS FYI

    i have come across this issue about 4 times this summer and wanted to post it here in case others are experiencing this issue. boats would run great at idle and under load but when you climb over 3500 the engine would bogg down and stall. and may keep running if you pull back on the throttle...
  6. C

    this will be fine, right?

  7. C

    2010 350 Mag MPI bravo 3 gaurdian mode issue. 5% power

    hi all, i have a boat that is going into gaurdian mode under load over 3000rpm, then when you pull back on the throttle, it goes back to 100%. the rinda says gaurdian cause: exhaust co. now i do not know if it is actually CO or that is as much of the word that would fit on the screen. there are...
  8. C

    bravo 3 outdrive/ water in bellows after transom service

    hey Guys, i got a problem. last spring i did an overhaul to a bravo set up and had to replace the gimbal bell housing due to a previous hack cutting into it and compromising the integrity( thats a whole different story). anyways, i drained the drive this fall and found water in the drive so i...
  9. C

    v6 cobra no or very hard to get into reverse. all cable tests done.

    ok, so i have a v6 omc, 1989. the drive wont go into reverse without man handlng it and sometimes not even then. the ESA assembly gets stuck in interrupt because of the tension i am putting on it. now, ive pulled the drive, checked the cables they are fine, shifts smooth with no drive in...
  10. C

    throttle bracket options while using a holley 4 barrel carb. anyone have a solution?

    a customer of mine has a brand new 5.7 marine engine oritinally intended for an INMAR set up. ( the intake has INMAR cast in it) and he wants installed in his boat, the boat is set up for mercruiser. the only difference is the intake and carb. the inmar intake appears to be a high rise with a...
  11. C

    anyone use API scantool? thinking about upgrading from the Rhinda

    if that is the appropriate word that is. is the API better than the Rhinda techmate pro?
  12. C

    ideas on how to remove a broken alpha gimbal pivot pin?

    the sholders of the pin, where the tool sits have broken so the tool cannot get a good bite to loosen and remove it. the space between the gimbal housing (bellhousing) and the gimbal ring is very close and i do not think i can get a sawzall into it without damaging the ring , the bellhousing is...
  13. C

    interesting find while diagnosing an overheat condition

    this boat came to me with an overheat condition, new manifolds and risers, new impeller assy, new thermostat and new sensors. after pulling the water feed hose going to the intake, i found some but not alot of water flowing @ idle then when upping the RPMS, the water flow cut down drasticly. i...
  14. C

    water leaking from top cap of upper gearcase on gen II drive

    i resealed an alpha 1 gen II and after starting it up there is water leaking out of the top cap, i removed the cap and replaced the rubber plug that seals up the water jacket and its still leaks, i cleaned all the crud from the 2 mating surfaces and still leaks. no water is getting into the...
  15. C

    how important is the water drain plug on an SX transom shield?

    the drain plug hole is stripped of its threads and i do not see any benefit or negative from not having it in place. this is the water drain plug on the outside of the transom shield on the port side. on the outside area of where the water intake hose connects to the unit. #'s 77 & 81 on the...
  16. C

    looking for phiotos of where the wires and cables enter the engine cowling on a 2003 sx200txrb

    i had to remove the wires and cables on this motor and their is a big molded grommet at the entrance to the motor. the grommet has large and small holes molded into it for each cable/hose and harness to sit into. if anyone has this engine and can take a close up photo for me , one that can...
  17. C

    looking for phiotos of where the wires and cables enter the engine cowling on a 2006 f250txr

    wrong model
  18. C

    2003 yamaha SX200TXRB wires and fuel line swollen and rotting away

    this engine wouldnt start and i found the battery cable going to the motor had severe voltage drop, once i got a new cable set i pulled the old one out of the loom only to come to fins a real big obstruction inside the loom, it looked like a snake with an animal in its throat. as i managed to...
  19. C

    2006 v/p 5.7 GI-E alarm sounding, power restriction/ limp mode

    for some reason , my post is not uploading
  20. C

    testing post

    when i post, it comes up with a blank screen
Back
Top