Logo

Search:

Type: Posts; User: racerone

Page 1 of 4 1 2 3 4

Search: Search took 0.16 seconds.

  1. Replies
    5
    Views
    28

    Re: Evanrude E15rcob

    Fuel that is going from the liquid state to the gaseous state needs heat.-----So the thermostat makes the motor run warmer / better at idle and trolling speeds.----The CAST IRON cylinders also expand...
  2. Replies
    16
    Views
    164

    Re: 2001 jhonson 70hp hard cold start

    Remove sparkplugs.-----Pull connecter apart in wiring harness that has the black / yellow stripe wire.----Pull flywheel with a rope.-----Do you see spark now ?
  3. Replies
    16
    Views
    164

    Re: 2001 jhonson 70hp hard cold start

    Some will argue.-----I would take the starter apart for inspection ./ new brushes perhaps / ohm check from commutator to the shaft.----Should read infinity.-----Easy work and costs ZERO $ to do an...
  4. Replies
    5
    Views
    37

    Re: Parts for 1979 40hp Mercury

    Your location ?-------Part numbers that you need ?
  5. Re: Johnson 15hp - Drops when gets to half throttle

    There are no temperature sensors on it to shut it down on overheat.----Test spark as suggested.---Test compression as suggested.------Check for water in the fuel tank.------Test run with timing light...
  6. Re: 90 Evinrude 150HP 2 stroke - Carb Primer/Choke inlet barb broken

    I should set up the lathe and make 50 or so of these fittings.
  7. Replies
    1
    Views
    31

    Re: Bypassing VRO automatic oiling system

    The 84 models did not come with VRO.-----But look up the 1983 / 84 pump and install it----- model # of your motor is ?
  8. Re: 1978 40 hp mercury water around top plug

    Step # 1 is to replace the water jacket gasket.----Easy job on a fresh water motor.
  9. Replies
    13
    Views
    62

    Re: 19?? Evinrude 4 hp

    Is the CO actually a CD , yes or no ?
  10. Replies
    87
    Views
    1,134

    Re: 77 Evinrude 85 h.p , will not idle

    Keep us informed on the progress.
  11. Replies
    13
    Views
    62

    Re: 19?? Evinrude 4 hp

    ??------100:1 is a ratio.--------Nothing to do with metric measurement.-----And you should run it at 50:1 ratio.------Calling or dropping in asking that information is still interupting a busy...
  12. Replies
    13
    Views
    62

    Re: 19?? Evinrude 4 hp

    They just do not want to be bothered by those calls today.----The CO makes it a 1985 model.----Every boat shop knows that !
  13. Replies
    12
    Views
    97

    Re: 1956 Johnson Seahorse 15hp

    You also need to adjust the low speed needle to compensate for fuel and local atmospheric conditions.-----The factory / book settings are only to get the motor to start and keep running.
  14. Re: 2003 Mercury 125 Saltwater - Replaced Oil Level Sensor, Alarm Won't Stop

    Does the alarm buzzer have an electronic circuit?-----If so then perhaps the buzzer itself failed.
  15. Re: Plz help. Pival thing at steering cable end

    Need to post pictures.-----This should be an easy thing to solve once we can see what you are trying to do.
  16. Replies
    2
    Views
    32

    Re: 1998 Johnson 150 won't run

    Pushing the key in while cranking it over ?
  17. Re: 1976 evinrude 70 hp outboard trim/run switch

    Model # is ?-----Any pictures of the trim / tilt system on this motor ?
  18. Replies
    9
    Views
    104

    Re: help to identify my mercury

    There are not many air cooled Mercury motors.----Stop running it .-----Post a picture or what horsepower is it ?
  19. Replies
    18
    Views
    163

    Re: 1990 40hp Mariner weak lower cylinders

    The whole concept of crankcase compression is mis-understood by many folks.-----Difficult to trouble shoot for some.
  20. Re: Evinrude 15hp model 15604A motor issues

    There is no SWITCH BOX on that motor.
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4