Logo

Search:

Type: Posts; User: Eric Hoare

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    17
    Views
    171

    Re: Johnson powerpack/coil wiring

    I have now been notified that all the power packs in their stock are wired the same and that they are getting onto the manufacturer to resolve the problem. All they had to do was check their flywheel...
  2. Replies
    17
    Views
    171

    Re: Johnson powerpack/coil wiring

    Ye, me too. I just looked up the new code they gave me and it looks nothing like mine however the one I bought from them was identicle with even the same code number on it. Its just that the wires on...
  3. Replies
    17
    Views
    171

    Re: Johnson powerpack/coil wiring

    they are now saying that my engine BJ60TL(CCR) is a 1998 model and not a 1988 as I had been informed which is another CDI number but how come the serial numbers where identical, this is very...
  4. Replies
    17
    Views
    171

    Re: Johnson powerpack/coil wiring

    just one other thing if you know it, what should be the volt reading from flywheel coil?? Thats not the 12volt for the charge system
  5. Replies
    17
    Views
    171

    Re: Johnson powerpack/coil wiring

    Cannot at the moment as they are both on my boat but the replacement part from America was the exact same number as the old one which was 583125 they both looked identical but it was only when it...
  6. Replies
    17
    Views
    171

    Re: Johnson powerpack/coil wiring

    I have just received a new Power Pack from America (expensive especially the extra charges) and found that the colour code on the half moon three pin connector of the new unit does NOT marry up with...
  7. Re: 2006 25hp 4 stroke will crank, won't run

    Sounds to me like some sort of break in your wiring system, Get an AVO meter and check continuity between your ignition and the fuel pump, check if there is a fuse in line. You should have a beep,...
  8. Replies
    17
    Views
    171

    Re: Johnson powerpack/coil wiring

    That diagram is the right one, many thanks
  9. Replies
    1
    Views
    169

    Re: How about stream fishing

    You are so right, my father introduced me to trout and salmon fishing as a kid here in the UK. I never took a box of flies with me, just a fly tying kit and copy the flies that were on the water at...
  10. Replies
    17
    Views
    171

    Re: Johnson powerpack/coil wiring

    Cheers for that, YES they are orange in the daylight they looked pink in artificial lighing.
    it is a 1988 60HP Johnson, on the lid it says VRO but it doesn't have the oil injection BJ60TLCCR....
  11. Replies
    17
    Views
    171

    Johnson powerpack/coil wiring

    On a Johnson 60HP 3 cylinder does it matter which wire from the power pack goes to which coil/spark plug?? ie Pink, pink/green, pink/blue
  12. Thread: Coils

    by Eric Hoare
    Replies
    28
    Views
    312

    Re: Coils

    I am one of those chrack pot people you are talking about but just answer his question.
    When a coil is wound the copper wires are separated buy greased paper and when fully wound more paper is unsed...
  13. Replies
    2
    Views
    161

    Re: First time boat project

    Hi Regi, you ask several questions but first welcome to the dreaded boat owners headaches. An aluminum hull can be left unpainted but first check the condition (all over including the inside) for...
  14. Replies
    6
    Views
    212

    Re: Tilt Trim Problems

    I had a simular problem with a tilt, I took the pump motor off, stripped it and cleaned the inside. then I connected blue to + and green to - and it worked then I reversed it and it spun the other...
  15. Re: 1997 Johnson 150; Engine Problems After Running for Awhile

    Is the head getting hot after being run for a while? Thermostats can cause the head to tighten up which will slow the running down. Even if water exits the "PP"
  16. Replies
    8
    Views
    245

    Re: 1969 9.5 evinrude water pump removal!

    With the two screw out try moving the gear leaver into forward this should not raise the leg but should enable the shaft to come out of the block. Then there are only two left, one is the tube for...
  17. Replies
    8
    Views
    245

    Re: 1969 9.5 evinrude water pump removal!

    Any good quality gear oil will do, don't be conned into thinking that it has to be "Marine" stuff, all you do is waste your money.
    Is the small block able to turn or move up and down now that you...
  18. Re: 2002 8.1HO-Trouble Starting after Shallows Stall-Not Going to believe the fix

    When diesel engines stall and not shut down by cutting the supply of fuel to the pump, it creates a back pressure through the pump, this pressure has to be released to allow the valves to reopen and...
  19. Re: Propeller shaft jammed, connecting bolts broken. Now what?

    You may find that your propeller shaft has bent. remove the boat from the water. unscrew the prop shaft gland packer mechanism from inside the boat, see if the shaft moves, if not. Check the "P"...
  20. Replies
    10
    Views
    215

    Re: Help with carburetor

    Are there two rubber pipe connectors on the bottom left where the fuel goes in? if there is, then you have an electric primer which is operated when you push the key switch in after using the primer...
Results 1 to 20 of 64
Page 1 of 4 1 2 3 4