Logo

Search:

Type: Posts; User: westrong

Search: Search took 0.00 seconds.

  1. Replies
    6
    Views
    1,538

    Re: Compression Check Issue

    The battery appears to be fine. I checked the voltage, load tested and all connection are clean and tight.

    Now, you mentioned the gear reduction starter...The opposite motor doesn't appear to...
  2. Replies
    6
    Views
    1,538

    Re: Compression Check Issue

    Yes with 5 or more plugs in the engine will crank. Take out any two plugs and the engine cranks once and that's it.

    I can't seem to get the "Multi-Quote" thing to work on this forum so I'll...
  3. Replies
    6
    Views
    1,538

    Compression Check Issue 1998 200 hp

    My dad was doing a compression check on a pair of 1998 200hp Johnson Ocean Pros. The first engine went fine during the check...removed all the plugs, turn the engine over...no issues.

    Now the...
  4. Replies
    0
    Views
    19,883

    "I just got an oil analysis ba

    "I just got an oil analysis back on a 1988 Hino Model 6-393N (967 Hours). They state that there is a high level of coolant in the crankcase oil. My question is besides the head gasket where else...
  5. Replies
    2
    Views
    1,454

    Thanks Mark...I'll give th

    Thanks Mark...I'll give them a call on Monday.
  6. Replies
    2
    Views
    1,454

    "Does anybody know a source fo

    "Does anybody know a source for parts for a Mercury gas generator, it's in a 1988 Sea Ray.

    Right now I'm looking for a starter...the local starter repair shop says they have to have one shipped...
  7. Thread: Stalling

    by westrong
    Replies
    20
    Views
    4,636

    "Well guys, so far so good. Th

    "Well guys, so far so good. The engine has about +20 hours since my last repairs and there has been no stalling. I'm not sure what the exact issue might of been but I'm not complaining."
  8. Thread: Stalling

    by westrong
    Replies
    20
    Views
    4,636

    Out of curiosity what should t

    Out of curiosity what should the ballast resistor cut the voltage down to at the coil?
  9. Thread: Stalling

    by westrong
    Replies
    20
    Views
    4,636

    "Well I've been busy thank

    "Well I've been busy thanks to you guys.

    I checked the pickup tube, measured fuel pump pressure, replaced all ignition parts, rotor, condenser, points, cap, coil, wires, plugs...etc.
    ...
  10. Thread: Stalling

    by westrong
    Replies
    20
    Views
    4,636

    "The filter going into carb is

    "The filter going into carb is new and clean.

    The canister fuel filter next to the fuel pump is new and clean. This is what I emptied and checked. I let the fuel sit then slowly poured it off. I...
  11. Thread: Stalling

    by westrong
    Replies
    20
    Views
    4,636

    "Okay, here's the latest.

    "Okay, here's the latest. I cleaned every connection from the battery to all components on the engine. During the sea trial the engine started loosing top rpm (3800 dropped to 3500). Bringing back...
  12. Thread: Stalling

    by westrong
    Replies
    20
    Views
    4,636

    I'll clean all the connect

    I'll clean all the connection this evening and let you know the results. This really has me baffled. I ran the engine the other day for about 4 hours and it never stalled but then again it will...
  13. Thread: Stalling

    by westrong
    Replies
    20
    Views
    4,636

    "I'm trying to help a frie

    "I'm trying to help a friend with his 4.3L 6 cylinder Cobra. The problem is the engine just "dies" at idle and won't restart. Sometimes it's as sudden as if you turn off the key, other times it...
Results 1 to 13 of 13