Logo

Search:

Type: Posts; User: faztbullet

Page 1 of 4 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    2
    Views
    33

    Re: 12V to Primer when switch is in run?

    Got the wrong purple going to primer or in wrong postion on switch
  2. Replies
    3
    Views
    23

    Re: Shimming tool kit

    It would be simpler to take new pinion on driveshaft to a dealer and have it checked. Be back on water quicker.
  3. Replies
    3
    Views
    22

    Re: 95 Evinrude 130 shift rod height

    No ...21-15/16.....21-1/4 is for 60° motors
  4. Re: 1986 Mercury Classic 50 - I cant find the right tool!

    A short piece of 4x4 with 7/8 hole so propshaft can stick thru, slide over shaft, install thrust washer and prop nut. 2lb hammer and pop on each side will walk it out.
  5. Re: E200STLERK piston to wall clearance ?

    Depends on the piston...bore to oversize spec...example .020 will be a finished bore of 3.705. Bore to 3.703 and use rigid hone to get 3.705.+/-.0001. If using a forged piston add .0015 for total of...
  6. Replies
    11
    Views
    120

    Re: 2 power heads in 3 years

    The failure are block design/water flow problem. It a modified copy of the Ficht cooling system. I will not build a 90° looper without it nor will I build a 60°without pressure testing block. Block...
  7. Replies
    4
    Views
    46

    Re: Hard to start 2007 115 EFI Johnson

    You got problems....
  8. Re: Mercury 2 stroke 135Hp wont rev up beyond 2800 rpm under load

    Need to check with timing light when problem happens. If one of the high speed sides of stator is bad spark will drop out when the switchbox transitions from low to high speed,,,,,
  9. Re: 1959 Mercury Mark 35a - Rewire Magneto to work off battery?

    The ignition switch grounds the mag to kill it. he doesn't have his key switch/wiring attached. The wires he attaches are for a bleeper, point close and it beeps. Attaching 12V to the mag terminal...
  10. Replies
    11
    Views
    120

    Re: 2 power heads in 3 years

    21479
  11. Re: New to Outboards need a little help with My Merc 175

    If you need parts order/look up 1986 150hp parts, If you need block parts lookup 1977-80 ser#4868998-5503246. Its a 150 .....
  12. Re: New to Outboards need a little help with My Merc 175

    Yes its a 150 with 175 decals...look behind that arm on block and you will see date made. The "can" is your enrichener .
  13. Replies
    11
    Views
    120

    Re: 2 power heads in 3 years

    Wasting your time if block don't have the water modifications... some rebuilders don't know how to do it or heard of it.
  14. Re: Ocean pro 150's will not rev past 4k at idle or 2500 under load

    That a good way to break piston skirts on those motors. Has it ever ran correctly or you new owner?
  15. Replies
    1
    Views
    27

    Re: 1997 Johnson 175 ocean runner help

    If its doing as you say its a weak charge coil on stator.....
  16. Re: New to Outboards need a little help with My Merc 175

    1) Gen1 blocks have no casting for oil injection pump....yours don't either so it old style motor.
    2) Its had newer 80's components added on. Most likely a 84 150 that blew and a old style powerhead...
  17. Re: Mercury 2 stroke 135Hp wont rev up beyond 2800 rpm under load

    Check spark as sound like it down a bank....
  18. Re: 70hp 3 cyl rebuild - cylinder block cover

    Those are broken off bolts.....
  19. Re: New to Outboards need a little help with My Merc 175

    Its a Frankenmotor...it a Generation1 2.0L block on a 1984 midsection. If a 175 block it has a different exhaust and if adapter plate wasn't changed it will suck water in the bottom 2 cylinders.
  20. Re: E200STLERK piston to wall clearance ?

    Mike the cylinder as ring gap not a good way to judge. Likely need bored if a open deck block
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4