Logo

Search:

Type: Posts; User: iang6766

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    16
    Views
    162

    Re: What prop on 2007 BF75D?

    One more question, is this boat dry stored or kept in the water? Just for the record, there is not a lot of difference between a 75 and 100, I had a customer upgrade from a 75 to 100 , same boat,...
  2. Re: 2016 honda 250hp low fuel pressure when first start

    Sounds like possible low voltage. If not, an O2 sensor could also cause this issue. Highly unlikely to be fuel related
  3. Re: BF130 Fuel pump failure and particles in downstream filter

    Boats.net only have 2 left, 800.00
  4. Replies
    12
    Views
    92

    Re: 2011 BF225 forward gear missing tooth

    That's pretty poor, seems the days of fixing things are fast disappearing. These gearcases can be rebuilt cost effectively if the correct tools are available. Having said that though, you will be...
  5. Re: Anyone experienced with Honda Bf50A lower unit?

    All the BF50 lower units are interchangeable but not the internals. The bearing carriers changed from the ring but retainer to the two bolt flange type. The cases were also improved and made with a...
  6. Replies
    12
    Views
    92

    Re: 2011 BF225 forward gear missing tooth

    Too, full rebuild/ reshim essential or you'll be doing it all again very soon
  7. Replies
    16
    Views
    162

    Re: What prop on 2007 BF75D?

    As Alan said , that cannot be a 10x17, they don't make a 10 inch prop for that size motor.
  8. Replies
    16
    Views
    162

    Re: What prop on 2007 BF75D?

    That boat should go well with a 13 1/4 x 17
  9. Re: BF40 (2018) New Motor Rpm Hunt/Sneeze/Surge

    And just for the record, any BF40 ECU will work on this engine irrespective of the year, it does not have to be the part number listed for that engine
  10. Re: BF40 (2018) New Motor Rpm Hunt/Sneeze/Surge

    Like I said, the ECU issue is a known problem, if there were connection issues, highly unlikely on new motor, there would be a fault logged. My turning to a new ecu was the fact that all sensor and...
  11. Re: BF40 (2018) New Motor Rpm Hunt/Sneeze/Surge

    Ask your dealership to try an ECM from another motor. I had one with very similar symptoms, 12hrs old, after thoroughly checking everything I tried a new ECM, problem solved. I have since discovered...
  12. Re: Wont start in HOT sun after sitting an hour

    Definitely vapour lock, check you water flow to and from the fuel cooler on the side of the vapour separator, see that they are clear and that water is flowing freely.
  13. Re: Ok it gets better Flywheel magnet broken in half.

    Loose magnets was a common problem on these, nothing unusual
  14. Replies
    1
    Views
    65

    Re: Honda BF 75 tiller handle problem

    It has double nuts (lock nut) on the through bolt to adjust the friction, simply loosen the lock nut using two spanners and then tighten the inner nut to the desired friction.
  15. Replies
    7
    Views
    121

    Re: Hard shifting BF90

    You will find the shift shaft driver in the mount case is seized in the nylon bushes. Unfortunately your only solution is to remove the power head, remove the shifter and clean and or replace the...
  16. Re: BF130 pressure and vacuum test after lower unit rebuild

    10 psi for 5mins is fine, for quicker check spray soapy water on all the seals
  17. Replies
    27
    Views
    321

    Re: Bf225 oil pressure alert at 3500 rpm

    I doubt the gauge and the oil pressure alert are wrong. The only issue you could have with the heads is a badly damaged camshaft bearing surface. I think this motor needs to be torn down and...
  18. Replies
    27
    Views
    321

    Re: Bf225 oil pressure alert at 3500 rpm

    These motors should run at around 80psi hot at 2000 rpm and above, I hate to say this but I think you have a serious mechanical issue, typically, thrust bearing failure comes to mind. This Is not...
  19. Replies
    29
    Views
    305

    Re: BF50D Fuel pump issue

    A quick and easy way to see if there is fuel in the VST is to attach a clear hose to the drain and hold up against the separator with the drain screw open and see where the fuel level is. If you have...
  20. Re: Ok new guy here. I saw somebody said they hate 4 storkes YEP

    People make the mistake of cleaning carbs and nothing else. The whole fuel system needs to be spotlessly clean from tank to carburettor or you're just wasting your time. Four stroke jets are very...
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4