Logo

Search:

Type: Posts; User: Ned L

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    2,487

    Re: 1955 Chris Craft Alignment issue

    A bit late but,..... I might also suggest that a side to side misalignment might indicate a bent strut.
  2. Re: 1957 Chrysler Crown generator voltage regulators

    Still chasing this problem. Unfortunately a conversion to an alternator is not a option. These generators are gear driven off the timing gear (there are no V-belts or pulleys on these engines. ...
  3. Replies
    5
    Views
    3,043

    Re: What Gray Marine Engine do I. Have?

    I'm guessing that is a flat head six that is probably based on the 226 CID Continental industrial engine. you should be able to find "226" cast into the block near the oil pan flange, probably under...
  4. Replies
    1
    Views
    2,432

    Re: Seeking Graymarine 4-112 replacement

    Your little Graymarine is based on a Continental industrial engine (fork lifts, compressors, generators, welders, etc). Once you identify what model Continental engine it is you should be able to...
  5. Replies
    1
    Views
    3,031

    Re: Gray Marine 6-150

    your Graymarine is a 'marinized' Continental industrial engine (compressors, fork lifts, welders, generators, etc) Once you identify what Continental engine it is many internal parts are as close as...
  6. Replies
    48
    Views
    11,198

    Re: Lets see your Chrysler powered boat

    https://uniim1.shutterfly.com/ng/services/mediarender/THISLIFE/002003758370/media/33119563092/medium/1500906085/enhance

    OK, I know it's old thread, ....... It's an old boat

    1957 Hubert Johnson...
  7. 1957 Chrysler Crown generator voltage regulators

    A real shot in the dark here, ...................
    I have a pair of 1957 Chrysler Crown M47's that need new voltage regulators for the generators. I have had no luck (zero, zilch, nothing)...
  8. Replies
    3
    Views
    3,578

    Re: Gray Marine 6 inline approx 1955

    A couple of things, either the engine is a Chris Craft (Hercules engine converted by Chris Craft), or a Graymarine (Continental engine converted by Graymarine). Either way, I presume this is a...
  9. Replies
    3
    Views
    5,092

    Re: 1946 Chris-Craft KB versus KBL

    Certainly David VaNess @VaNess engineering in NJ can tell you all the details.
  10. Thread: Gray marine gas

    by Ned L
    Replies
    1
    Views
    5,995

    Re: Gray marine gas

    The "109" is based on the Continental "F226" industrial engine (226 CID) and that is how you need to have it looked up at your local auto parts store to find parts.
  11. Re: 1949 Chrysler Crown engine -- part no. and supplier questions

    A bit late for a reply, ....... I don't think anyone makes new manifolds for the Crown or Ace. (the link above is to Barr marine, and they do not make them any more)
    Basic engine parts are...
  12. Replies
    1
    Views
    404

    Chrysler crown M47 (1957) head studs

    Any suggestions on where to buy head studs & nuts for a pair of Chrysler Crown M47's?
  13. Replies
    1
    Views
    449

    Chrysler Crown M47 fuel pumps

    I am looking for the part numbers (or source) for the fuel pump for a Chrysler Crown M47 (1957).

    Thanks!
  14. Replies
    2
    Views
    5,823

    Re: transmission jumping out of gear

    is this a hydraulic or mechanical reverse gear??
  15. Re: Any suggestions on how to manually rotate a flywheel-forward 283?

    Rick: I really like your idea of 'modifying' an old starter motor, very good! I completely agree with you about possibly damaging a ring gear tooth by using a prybar (I probably shouldn't have...
  16. Replies
    8
    Views
    5,151

    Re: removing tranny from 109

    Good news!
  17. Re: Any suggestions on how to manually rotate a flywheel-forward 283?

    In similar situations I've had luck using a big prybar or crowbar under the edge of the motormount/flywheel cover and catching a tooth on the ring gear. If you are careful and don't let the end of...
  18. Replies
    8
    Views
    5,151

    Re: removing tranny from 109

    Not sure what you mean by "disengaged"? It is a pretty easy job on both the Paragon hydraulic and manual versions. Remove the bolts holding it to the rear bell housing and it pulls right off.
  19. Replies
    2
    Views
    1,877

    Re: 283 engine rebuild - assembly questions

    Mike: Glad to hear you are back at it! When I put mine back together I used a very little bit of Permatex (#2 I think, - the non-hardening type) on the gasket. I think I would recommend using...
  20. Thread: The Proper wheel

    by Ned L
    Replies
    6
    Views
    1,034

    Re: The Proper wheel

    What RPM are you getting out of the engine when wide open? If you are hitting hte rated RPM (guessing about 4500 for that engine) then you need more prop (I'd try a 13x13)
    ("Wheel" is an old time...
Results 1 to 20 of 37
Page 1 of 2 1 2