Logo

Search:

Type: Posts; User: Rwbutler

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    5
    Views
    23

    Re: HELP 1996 johnson faststrike j150gled

    Are you pumping up primer bulb each time you want to start it?
  2. Replies
    5
    Views
    35

    Re: 1969 Johnson 85hp starter problems?

    Start with avoltage drop test. Testing is cheaper than thowing money at it. Check out C.D.I. 's guide on this site.
  3. Replies
    5
    Views
    23

    Re: HELP 1996 johnson faststrike j150gled

    Does it do this when you first leave the ramp?
  4. Replies
    18
    Views
    108

    Re: Crosstown rings

    iI apologize,that was a stupid statement,
  5. Replies
    18
    Views
    108

    Re: Crosstown rings

    Im not missing it ,I agree totaly. Racer said it was a bad design,I was wanting to know why he thought the ring was a bad design.right now i dont care. End of post.
  6. Replies
    18
    Views
    108

    Re: Crosstown rings

    No,but have held most of them in my hand.other than diameter and that i think yamahas taper is differnt,whats not the same?
  7. Replies
    1
    Views
    19

    Re: 225 fuel injection Evinrude year 2000.

    Bell,whistle,horn,lites? Gained RPM again to what? Did it only do this once?how did it run the rest of day?more info is needed.in answer to your guestion. Spark,fuel,compression,and the ability to...
  8. Re: 1995 Johnson 200 OceanRunner Low Oil Alarm

    The lo oil wire at motor is tan with black strip. Your red and black wire was added by someone.assume red goes to tan/black,,black to block ground.
  9. Replies
    18
    Views
    108

    Re: Crosstown rings

    Its original,I bought it in 79, Ran on 89octane or higher ,E/J,oil,turner every year.
  10. Replies
    18
    Views
    108

    Re: Crosstown rings

    You would have thought if pressure back rings were a bad design they (evinrude,yamaha,johnson,etc) wouldn't still be using them today.One thing for sure,ring breakage is common on crossflows.
  11. Re: What came first...SLOW Mode or no water pressure?

    Remove hose from back of w/p gauge,remove other end of that hose at motor. Get one of those can of air (for cleaning key board) spray into gauge.Does gauge work? Spray into hose,does air come out...
  12. Replies
    2
    Views
    24

    Re: Johnson 225 V6 1988 SLOW mode

    When the alarm sounds and SLOW is activated,is the motor hot at top of cly.heads?
  13. Replies
    18
    Views
    108

    Re: Crosstown rings

    Please describe "that ring"
  14. Re: Evinrude sportsman 4425 1.5hp fuel problem

    Check this:brazillianconnection.comm if you are trying to restore. Water pump impeller are not available.that motor has two.
  15. Replies
    18
    Views
    108

    Re: Crosstown rings

    Probably see it(broke rings)more in the V4 because their more of them out there. Drop a ring in a big V6 and there ain't enough left to tell what happened.
  16. Replies
    18
    Views
    108

    Re: Crosstown rings

    That's the way it was taught to me also. Any idea why Racer says it's a design issue?pressure back rings are used in many engines.
  17. Re: Evinrude sportsman 4425 1.5hp fuel problem

    I would not spend money on that carb.
  18. Replies
    18
    Views
    108

    Re: Crosstown rings

    My spelling. Crossflow loopper my autocorrect is doing that.
  19. Replies
    18
    Views
    108

    Crosstown rings

    No,I don't know why the top ring breaks on 3.5 loppers and crosflow.please tell me your opinion. I need to know cause I'm still running a'79 100 with hi ring pistons.
  20. Replies
    10
    Views
    65

    Re: 1990 Johnson 115 bogs under load

    Just wanted to see if YOU were out there.
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4