Logo

Search:

Type: Posts; User: Jerryjerry05

Page 1 of 4 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    3
    Views
    39

    Re: 1996 75 HP Force Engine

    Myself , I've never had a sending unit go bad.
    I always replace the buzzer with a 12v horn from a car or motorcycle.
    You can hear them a lot better than the original buzzer.
  2. Replies
    7
    Views
    41

    Re: 1996 Force 75 HP Hard Steering

    The 3cyl. with one carb is a bit troublesome.
    The top cyl. sometimes suffers from lack of fuel and that results in a scored piston and cylinder walls.
    One thing is add a bit more oil to the gas....
  3. Replies
    7
    Views
    41

    Re: 1996 Force 75 HP Hard Steering

    Remove the zerk for expansion.
    Try heating it too, sometimes they get clogged and won't take grease.
  4. Replies
    3
    Views
    39

    Re: 1996 75 HP Force Engine

    Might not be the sender?
    Try a new buzzer or horn.
    Most time the buzzer can't be heard anyway, I add a car horn or motorcycle horn.
    They can be heard a lot better.
    If you add a new horn? then...
  5. Replies
    7
    Views
    41

    Re: 1996 Force 75 HP Hard Steering

    If the king pin is seizing or very hard to turn the motor:
    The bearings or bushings in the top and bottom of the kingpin: most cases there's only one grease fitting for that area.
    IF??? they are...
  6. Re: ISO prop for a chrysler 1979 559H9L

    Look up marine salvage yards in the mid-west.
    There's a few in Mi.
    A bunch in Ohio, Indiana, Illinois etc.

    Or find a prop shop that can re-hub your old one.
    Millers Island in Maryland....
  7. Re: 1972 Chrysler 55hp Ignition Coils Failing

    I'm not sure how it's done but you can change the ignition system over to an automotive coil.
    Some one might be able to add the procedures??
    Look on u-tube?
  8. Thread: 559h9l

    by Jerryjerry05
    Replies
    8
    Views
    58

    Re: 559h9l

    There's no one I know that can spin the hub by hand when it's bad.

    The reason for the rubber is to save the metal shafts and other components.
    The hub spins before the prop shaft, drive shaft,...
  9. Thread: 559h9l

    by Jerryjerry05
    Replies
    8
    Views
    58

    Re: 559h9l

    There's nothing(no other keys) other than the prop needing a hub that can make it slip.
    Scribe a line on the hub, go for a ride , check the line to see if it has moved????
  10. Re: 1985 force 856F5A no spark cylinder 3

    Ebay again is about the cheapest or

    http://standardmagneto.com/Marine/force.html
  11. Replies
    10
    Views
    200

    Re: Control cables '85 85hp

    Great, thanks for the update.
  12. Re: Chrysler 55 hp Model 559HA 1970 motor problems

    Other than the idle might be a bit low??? it sounds ok from the video.
    In N 1100-1200 in gear in the water 800rpm's
    Compression?? as long as it's within 5-10# it should be ok.
  13. Replies
    0
    Views
    90

    2004 150 Yam buzzer going off.

    2004 Yam 150 carb.150TXRD
    The motor runs GREAT up to 3800-3900 and then the alarm starts.
    It's NOT overheating, I used a heat gun and checked the temps on each cylinder.
    Not getting anywhere's...
  14. Replies
    10
    Views
    200

    Re: Control cables '85 85hp

    ebay.about 45$ https://www.ebay.com/itm/403497631166?epid=1038188306&hash=item5df2553dbe:g:p08AAOSweP5iF89S

    Check at your local boat store.
  15. Replies
    10
    Views
    200

    Re: Control cables '85 85hp

    Morse cables.
    ANY!!! marine place should be able to get/have the cables you need.
    Make sure you get cables long enough.
    How are outboard remote cables measured?



    Measure from control along...
  16. Replies
    8
    Views
    255

    Re: 15HP 152BA Adjusting and Running

    Enjoy !!!!
  17. Replies
    29
    Views
    9,106

    Re: Trim/Tilt removal Force 125

    RRitt passed away a few years ago.
    He was the go to guy for Force [email protected] his daughter tried to do some repairs after he passed but didn't have much success.
    Try here for [email protected] repairs with pics:...
  18. Replies
    10
    Views
    766

    Re: Force 125 Coil Replacement

    It's supposed to move.
    That's normal.
  19. Replies
    10
    Views
    766

    Re: Force 125 Coil Replacement

    Testing trigger leads: the wire breaks under the shrink wrap/glue at the connector.
    I replace them ALLLL. Stator too.
    Tugg on the thin wire end at the connector.
    If it's bad then the wire...
  20. Replies
    5
    Views
    125

    Re: Model 2004 SN 1252 1969 Chrysler

    Wow good weld job!!! That's a new one on me.
    Clean it up and paint it.

    The linkage pic: couldn't really tell, maybe a few more from different angles??
    The center of the pic is a ball connector,...
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4