Logo

Search:

Type: Posts; User: Rhigley

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    25
    Views
    625

    Re: 1990 xp 100 Evinrude

    I think I see what's going on with the thumb rollers, the bottom one looks like it centers the cam to the center notch and the one under the fly wheel is the timing. Dose this sound right?
  2. Replies
    25
    Views
    625

    Re: 1990 xp 100 Evinrude

    That's what I am trying to do. I'm hoping all is well the way it is ,but if it way off I want to try to bring it back to the 28..I see 2 thumb screws with locking nuts on them. One is about mid...
  3. Replies
    25
    Views
    625

    Re: 1990 xp 100 Evinrude

    I'm checking to see if is what the book says it should be (4 ATC and 28 BTC) and if is was not, I would like to try and get it set.
  4. Replies
    25
    Views
    625

    Re: 1990 xp 100 Evinrude

    I have a manual from Seloc and looking to see what thumb screw I should be moving to set timing. I have one about in the middle of the throttle leakage and one top under the fly wheel. It looks to me...
  5. Replies
    25
    Views
    625

    Re: 1990 xp 100 Evinrude

    Got the fuel pump installed and the plug for the pulse. Thanks everyone for all your help. I'm going to check the timing on the water, seems to be the easiest way to go.
  6. Replies
    25
    Views
    625

    Re: 1990 xp 100 Evinrude

    I was just looking at Low's and found what looks like what I need .Thanks
  7. Replies
    25
    Views
    625

    Re: 1990 xp 100 Evinrude

    Got the pulse connection out and now I'm trying to find the plug to replace it. My local boat shop is closed for the holidays so I'm kind of stuck .Don't want to mess up the threads on the block. Not...
  8. Replies
    1
    Views
    738

    trim gauge on Evinrude 100 XP

    I bought a cheep trim gauge for my boat. I am trying to wire it up before I drill the hole in the dash. I hooked up the white with light brown strip to the signal post. Ground (black) to ground and...
  9. Replies
    13
    Views
    236

    Re: How to set WOT on 1990 evinrude 100

    I think that will be best for me also to get out on the water for a test run anyway after I get the new fuel pump on.
  10. Replies
    13
    Views
    236

    Re: How to set WOT on 1990 evinrude 100

    not sure I have all the info I need. Do I disconnect the remote cable from the fuel side and then place spark advance all the way foreword or do I need to bypass some electrical switch to let the...
  11. Replies
    13
    Views
    236

    Re: How to set WOT on 1990 evinrude 100

    only one on each head
  12. Replies
    25
    Views
    625

    Re: 1990 xp 100 Evinrude

    cool.. thanks do you know what size plug I need for the pulse hole? I tried to remove it but couldn't find the size of the nut. Is it metric?
  13. Replies
    13
    Views
    236

    Re: How to set WOT on 1990 evinrude 100

    it has an electric choke
  14. Replies
    25
    Views
    625

    Re: 1990 xp 100 Evinrude

    I pulled the old VRO/fuel pump out and ready to get the fuel pump only for the 88. I know the inlet is from the fuel filter and I think the outlet goes to the split manifold to the carbs. I have one...
  15. Replies
    13
    Views
    236

    Re: How to set WOT on 1990 evinrude 100

    what if I ran the motor for a bit to warm it up before I set the timing. Would that eliminate having to by pass the fast start?
  16. Replies
    13
    Views
    236

    Re: How to set WOT on 1990 evinrude 100

    Ok. the book says 28 deg. Can I set this with a timing light and grounding all 4 leads with the switch by-passed or should it be in the water running WOT ? I have not been able to check this because...
  17. Replies
    13
    Views
    236

    How to set WOT on 1990 evinrude 100

    I'm looking into checking the WOT setting on my motor. I changed out the prop but they look to be about the same but I get a reading of over 6000 rpm when WOT is set. Other than prop and throttle is...
  18. Replies
    25
    Views
    625

    Re: 1990 xp 100 Evinrude

    I pulled off the prop I was using (Stiletto 21317 01317) and placed the one that came on the motor back on (13 1/4 x 17) Will this make a difference on my boat?
  19. Replies
    2
    Views
    100

    Re: Fuel Pump for XP 100

    Thanks. That's the way I will go
  20. Replies
    2
    Views
    100

    Fuel Pump for XP 100

    I know I need a fuel pump repair. My question is what is the best way for me to go. Rebuild fuel pump on the already bypassed VRO unit or go with the 0438556 - Fuel Pump (for 88) ?
Results 1 to 20 of 29
Page 1 of 2 1 2