Logo

Search:

Type: Posts; User: bperry

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Re: power trim and tilt stopped trimming and tilting

    Remove engine cover and check fuse on engine, Mine was supposed to have a 20 amp and PO had put in a 10 amp. It blew and my tilt and trim or starter would work. Replaced with 20 now fine.
  2. Replies
    1
    Views
    1,293

    Re: fuel gauge problem

    just took the cork float off the sending unit and it barely floats, with the weight of the sending unit it does not. now I have a fishing cork floating in the tank and it worked but came off. time...
  3. Replies
    1
    Views
    1,293

    fuel gauge problem

    I have a 20 gallon fuel tank in my boat and the fuel gauge does not work properly. If I remove the sending unit and move it manually everything works. I have put the sending unit in a bucket of water...
  4. Replies
    0
    Views
    119

    runs well at slow, not higher speed.

    This motor is running fine at about 1000-1500 rpm. I try to accelerate and it bogs down. only have been in water twice. after first time i checked compression, changed all 6 plugs and added a water...
  5. Re: in process of removing oil injection NEED HELP

    got it all out and blank off plug in. new plug in crankcase. Now to remove on board tank and hoses. then all premix.
  6. Re: in process of removing oil injection NEED HELP

    UPDATE got that piece out. attempting to remove drive shaft for pump. I see in the book it is a worm gear. I removed all plugs so I could rock the eng while attempting to remove shaft. still no luck....
  7. in process of removing oil injection NEED HELP

    I have removed the oil pump and I have the blank off kit. How do I get this piece out so the blank off kit will go in. I have turned it with a screwdriver, attempted to pull out with needle nose....
  8. how do I remove oil injection from mercury motor

    I recently purchased this boat and the oil injection appears not to be working. I am running off a premix tank and every time I put oil in the main tank and run the motor the oil siphons out and runs...
  9. Replies
    3
    Views
    137

    Re: engine running poorly

    I guess I am talking to myself but I find oil is coming from the main oil tank . The 2 psi check valve on the oil line coming from the main tank I think is bad. The hose from the check valve vent...
  10. Replies
    3
    Views
    137

    Re: engine running poorly

    After reading the manual oil goes from the oil pump to the fuel pump outlet and mixes with fuel. Why would pure oil run out the air intake of the bottom carb???
  11. Replies
    3
    Views
    137

    Re: engine running poorly

    Just took compression and spark test. all cylinders between 120 and 125 compression . found oil dripping from bottom carb. I know the injection oil goes into each carb where it can mix with fuel....
  12. Replies
    3
    Views
    137

    engine running poorly

    My 1993 150 HP mercury is running poorly. Seems to run about 1/2/ throttle and no more. alarm going off, running on premix 6 gallon tank for test. It runs for a few seconds and shuts down shift to...
  13. Replies
    0
    Views
    111

    problems with new to me mercury

    first not getting air to remote tank to push oil to the engine tank on the oil injection system. Next tachometer is not working. eng is charging the battery at 14.6 volts. the tach moves a little but...
  14. Thread: Oil injection

    by bperry
    Replies
    1
    Views
    2,834

    Re: Oil injection

    After further investigation and reading the book I find the line that was disconnected was from the oil injection pump discharge. fixed that. took the boat out and ran good on pre mix tank. gallon of...
  15. Thread: Oil injection

    by bperry
    Replies
    1
    Views
    2,834

    Oil injection

    recently purchased this boat with a 150 mercury outboard. It has a large abt 2 gallon oil tank under rear seat and a small tank on engine. I put a gallon of oil in the tank under the seat. Installed...
  16. Replies
    6
    Views
    2,460

    Re: Oil injection cap for tank on top of engine

    Installed the new cap. hooked to the blue and black wires. waiting for the rain to stop so I can try it out
  17. Thread: cleat on deck

    by bperry
    Replies
    1
    Views
    3,986

    cleat on deck

    Just purchased a 1989 hurricane. It is fiberglass and on top looks like a pontoon. One cleat is broken. I purchased a new one and attempted to remove old one. screws spin like there is a nut on the...
  18. Replies
    0
    Views
    1,426

    Oil injection wiring

    Just purchased a Hurricane with a 1993 mercury eng. PO had put a boat plug in the oil tank on top of the engine. he has a black and a blue spliced together just at edge of tank on the engine. I have...
  19. Replies
    6
    Views
    2,460

    Re: Oil injection cap for tank on top of engine

    Thanks for the answer. I still have a blue and black wire spliced together. that is on the engine. tank had no cap. It had a boat plug in it; I ordered the cap and noticed the wires so looked at the...
  20. Replies
    6
    Views
    2,460

    Re: Oil injection cap for tank on top of engine

    guess I should have started a new thread??
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4