Logo

Search:

Type: Posts; User: RicardoMarine

Page 1 of 4 1 2 3 4

Search: Search took 0.07 seconds.

  1. Re: Engine miss and new rattle developed in exhaust manifold

    I cannot emphasize enough the importance of locating true TDC. That would be my first priority.


    Also, I think that I have exhausted my efforts in helping you.


    As I see it, you have two...
  2. Replies
    4
    Views
    54

    Re: Fly wheel grease fitting

    ..................




    .
  3. Re: Volvo 5.7 Penta Exhuast Manifold Rear Drain Reduction Sleeve & Plug

    ....... and use a six point wrench!
  4. Replies
    4
    Views
    54

    Re: Fly wheel grease fitting

    Are you asking about a lubrication port on the top of your flywheel cover?
    If so, that would be for lubricating the PDS bearing(s).
    If you have not been servicing it, it's time to replace the PDS...
  5. Re: Engine miss and new rattle developed in exhaust manifold

    ...................



    Good luck. Hopefully you'll get it sorted out soon.




    .
  6. Replies
    2
    Views
    52

    Re: 2005 Volvo penta 8.1 over heating

    Did you check the replacement impeller against the previous impeller to ensure that the depth was correct?
    When the impeller is placed in the pump body, it should sit proud by approx .010" or so. ...
  7. Re: Engine miss and new rattle developed in exhaust manifold

    ..................
  8. Re: New and have out drive question(s)

    If you acquire an OEM Service or Work Shop manual, be sure to look at the section that pertains to a C or later transmission..... (i.e., post A transmission)!

    No Seloc, and no Clymer! OEM ONLY!...
  9. Re: Engine miss and new rattle developed in exhaust manifold

    .............
  10. Re: New and have out drive question(s)

    ......................



    As Bob suggested, store the boat with the drive down and aiming straight forward.
    Lift the drive no more than need be when on the trailer.
    Do this, and you will...
  11. Re: Aq280PT and 290A V8 PDS bearings/u joints.

    .............
  12. Re: Engine miss and new rattle developed in exhaust manifold

    ............
  13. Re: Question about emptying carb during periods of non use

    ............
  14. Replies
    1
    Views
    49

    Re: firing order- 1999 502 mag

    The 502 Mag firing order should be the same as it's predecessor ......... 1-8-4-3-6-5-7-2 .
  15. Re: Engine miss and new rattle developed in exhaust manifold

    ............
  16. Replies
    2
    Views
    54

    Re: 4.3 omc starter issues

    ..................





    Ncycenas, if you end up returning that starter motor, I would suggest picking up a HTGR/PMGR motor.
    It will be smaller, will consume less Amps and will spin your...
  17. Re: aq125 pouring antifreeze out of hole in block on bottom of rear intake manifold

    Were you able to fit a Metric threaded plug into that port?
  18. Replies
    6
    Views
    104

    Re: Timing question

    .........
  19. Replies
    5
    Views
    105

    Re: 5.0L Target RPM at WOT?

    Ditto and Ditto.
    You can try props until the cows come home, and you'll never get it quite right.


    .
  20. Re: Engine miss and new rattle developed in exhaust manifold

    ............


    Recap:

    Verify true TDC. If the TDC marks are inaccurate, your ignition timing will be just as inaccurate.

    If your OEM work shop or service manual gives you an advance curve...
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4