Logo

Search:

Type: Posts; User: bondo

Page 1 of 4 1 2 3 4

Search: Search took 0.03 seconds.

  1. Re: Pontoon deck, fiberglass covered pressure treated plywood?

    Ayuh,.... I wouldn't,.... The chemicals used to treat the plywood, causes massive corrosion to the hull's aluminum,.....
    'n it Will leech out, 'n down through the screw/ rivet holes,....
  2. Re: 2001 Wellcraft Tournament Addition Walkaround

    Ayuh,.... That's 'bout 13 Grand more than I'd pay for an ole barn-find boat, that needs that much work,....
  3. Thread: 3.7 to 4.3 swap

    by bondo
    Replies
    18
    Views
    246

    Re: 3.7 to 4.3 swap

    Ayuh,..... 1st thing to do is figure out Why it's runnin' so hot,.....

    I'm guessin' the "Smoke"yer seein' is steam burnin' off condensation in the oil,...
  4. Re: Thru Hull Exhaust. Do it? Don't do it? Opinions?

    Ayuh,.... I did it 20 years ago, 'n have spent those 20 years tryin' to make it Quieter, ever since,....

    No Way, I'll ever do it again to another hull,....
  5. Re: 2000 mercruiser 3.0 hard start and idling isues

    Ayuh,.... That's exactly where I would start, 'n throw in a compression test to get a baseline of the motors overall general health,.....
  6. Re: Newbe to MerCruiser 4.3 MPI or inboards as a whole

    Ayuh,.... You adjust the shift cables at the shift switch,....
    If it can't be adjusted properly, ya Replace the lower shift cable, then adjust it,....



    There's the slave solenoid, which...
  7. Re: Crusader 454: Air in raw water intake strainer (Starboard engine)

    Ayuh,..... Sounds like a restriction at the pick-up, seacock, or hoses to the strainer,....

    On a new to you boat, the 1st thing I'd do is replace the raw water pump impellers,.......
  8. Replies
    12
    Views
    160

    Re: Possible freeze damage help please

    Ayuh,.... If ya Did, 'n got 'bout 3 gallons of water, ya Might be Lucky,....

    When I pull the drain plugs, I poke the holes with a deckscrew to dislodge the rust, dust, 'n debris that gathers in...
  9. Replies
    7
    Views
    86

    Re: Prop id, need help

    Ayuh,.... At 2" bigger, it'll be Ok as a "Get ya back to the ramp" prop,.....

    Runnin' it is probably gonna lug the motor, so don't use it as a run, 'n gun, regular use prop,....
  10. Thread: volvo penta

    by bondo
    Replies
    0
    Views
    92

    Re: volvo penta

    Yer Close,.... The Volvo forum is the next 1 down on the main page,.....
  11. Thread: nova craft

    by bondo
    Replies
    1
    Views
    98

    Re: nova craft

    Ayuh,.... What, Exactly do ya need to know,..??

    What motors, 'n drives are there now,..??

    There's several ways to get where ya wanta be,....

    Basically, ya glass in the transom, 'n bolt...
  12. Re: Battery requirements for 1983 OMC 302FTHRCTR 3.0L

    What the 'ell is a "semi traction battery",..??
  13. Thread: 3.7 to 4.3 swap

    by bondo
    Replies
    18
    Views
    246

    Re: 3.7 to 4.3 swap

    Because OMC has been outa business for several Decades,......
  14. Replies
    8
    Views
    179

    Re: 5.7 oil cooler changeout

    Ayuh,..... I've found havin' a Hose Pick, makes takin' water hoses off, much, Much easier,.....

    One of those tools, that once ya got one, ya can't figure out just how ya ever got by without...
  15. Re: Correct locations for water heater installation. Stroker 383, 2007

    Ayuh,.... It's just Spam Rick,..... A Hvac company in jersey,...
  16. Thread: 3.7 to 4.3 swap

    by bondo
    Replies
    18
    Views
    246

    Re: 3.7 to 4.3 swap

    Ayuh,... That's not true,.... Only the Long Block motor will easily swap,....

    Everything OMC has to go, 'n be replaced with Mercruiser dressin's,.....
  17. Thread: Freeze Damage

    by bondo
    Replies
    18
    Views
    261

    Re: Freeze Damage

    Ayuh,.... Can't tell ya where the core plugs are, unless ya tell Us what motor ya got,....
  18. Re: 2001 Wellcraft Tournament Addition Walkaround

    Ayuh,.... Unless it starts, 'n runs,... Knock a zero off the end of the askin' price,....
  19. Re: Replace head gaskets as preventative maintenance?

    Ayuh,.... If ya rebuild the heads,.... Yes, you'll need new head gaskets,....

    Otherwise,...........
  20. Re: Call for help, again. I知 putting the 3.0 back together.

    Ayuh,..... Yer motor was starvin' for gas before, so it'll still be starvin' for gas later if ya don't fix the fuel delivery system,.....

    The lean condition is probably the root cause of yer...
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4