Logo

Search:

Type: Posts; User: hondadude

Page 1 of 4 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    2
    Views
    48

    Re: Honda 259 Nema 2000 t

    Is this what you are looking for?

    http://cdn.powerequipment.honda.com/marine/pdf/misc/nmea2000_pgn_list.pdf

    Mike
  2. Replies
    4
    Views
    120

    Re: BF100 Water in engine oil Please Help

    The wide open throttle should be approximately 151 psi. Most likely, you have not opened the throttle all the way....you would have to put the motor in gear to get it to wide open throttle, due to...
  3. Replies
    4
    Views
    97

    Re: Honda 45A outboard

    There are essentially three basic models of the 35 -50 hp Honda. The early ones, like yours have a manual choke on carburetors, the A4 models (2004 and later A models) have a bystarter arrangement...
  4. Replies
    4
    Views
    98

    Re: Honda BF8D No Spark

    As I hit send, I thought of one other thing to check. I have seen the ground wire for the cdi lose continuity, due to the wire being broken inside the insulation. So, visually, you can not see the...
  5. Replies
    4
    Views
    98

    Re: Honda BF8D No Spark

    It is a 2001. Model is BF8D1.

    When you test the spark, be sure that both coil leads are connected. They both fire at the same time.

    The complete circuit goes from ground, through one...
  6. Re: bf75 wont run unless primer button is pressed

    Are you sure that the button is not the safety switch? Unless it is a special installation, Honda's choke control has been either a toggle switch, you push the key in (to choke) or in a side mount...
  7. Replies
    19
    Views
    196

    Re: Honda bf75a carbs

    If you can not post the pictures, upload them to something like Google Photos, Drop Box or similar cloud depository.

    Then post the link on the forum.

    -A couple of other things to check before...
  8. Replies
    11
    Views
    163

    Re: BF50 idles rough, but runs OK?

    As for the valve clearances. Here is a video, that goes in great detail on the adjustments. It is on a Honda 40, which is essentially the same as your 50. The specs and measurements will be the...
  9. Replies
    11
    Views
    163

    Re: BF50 idles rough, but runs OK?

    The plastic silver cap on the screw on the top carburetor is a cap put onto the screw with loctite. The screw itself is brass. The new screws consist of the brass screw, o ring and separate cap. ...
  10. Replies
    19
    Views
    196

    Re: Honda bf75a carbs

    The compression is not bad. It would be good if it were closer to 200, but it should still run ok.Are all plugs fouled when it runs bad? Or just one or two?

    Have you checked the timing marks. ...
  11. Replies
    11
    Views
    163

    Re: BF50 idles rough, but runs OK?

    The EPA has Honda put a limiter cap on the screws so they are not tampered with.

    A different screwdriver will not help.

    Mike
  12. Replies
    11
    Views
    163

    Re: BF50 idles rough, but runs OK?

    It appears that you did not remove them, so they are hopefully set correctly.

    One way to get out the broken one is to take a center punch and punch a hole near the edge and then another on the...
  13. Replies
    19
    Views
    196

    Re: Honda bf75a carbs

    You can see if the butterflies are moving by disconnecting the connecting linkage and operating each one by hand, one at a time. They should move freely and spring back to open when not held down.
    ...
  14. Re: trouble shooting Honda BF15D6 shifting rod problems

    When the motor is in forward, the prop should be locked when you turn the prop counterclockwise. It may or may not turn or ratchet if you turn it clockwise.

    When the motor is in reverse, the...
  15. Replies
    19
    Views
    196

    Re: Honda bf75a carbs

    Post the frame serial number and we will check the year.

    First check to be sure that the oil level is not too high. It should be approximately 1/4 inch below the full mark. High oil can foul...
  16. Replies
    11
    Views
    163

    Re: BF50 idles rough, but runs OK?

    To check timing.....

    Align the arrow next to the T on the cam with the arrow next to the T on the top of the cylinder head. Then look for the T with a mark next to it on the outside of the...
  17. Re: trouble shooting Honda BF15D6 shifting rod problems

    Your measurement is good and it sounds like all is shifting as it should.

    Mike
  18. Replies
    3
    Views
    126

    Re: Bf150a6 blowing number 5 fuse

    Good job hunting!

    I hope that is the extent of your problems with the 150. It is a great motor.

    Mike
  19. Re: 2007 BF90D tach reads zero but runs fine

    Hopefully, you can get it to fail for a while, so you can test it.

    Here is a link to a Faria site that explains how to troubleshoot a tachometer. If you have 12v at the gauge and a signal...
  20. Re: What to look for when buying a 1997 90hp Honda four stroke motor?

    Per the manual....compression should be 213 plus/minus 14 psi. If you get somewhere near 190 from cranking, that should pretty good.

    Just so you know, around this vintage of the Honda 90, it...
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4