Logo

Search:

Type: Posts; User: chawk_man

Page 1 of 4 1 2 3 4

Search: Search took 0.03 seconds.

  1. Re: 2016 honda 250hp low fuel pressure when first start

    Jamie - WOW, we haven't heard from you for a long time. Welcome back.

    Could you give more explanation on "struggles for fuel at first." What exactly is it doing. How do you know that?
  2. Re: 2002 BF225 Intermittent Power Loss and Bucking

    You are correct on what causes an automatic power down - overheat, which will shut down the engine in 20 seconds if not cured, and low oil pressure, which will not shut down the engine. So, you need...
  3. Replies
    12
    Views
    167

    Re: Dreaded $270 dollar 02 sensor

    All this is covered in Honda service bulletin #70. If you need a copy, send an e-mail to me at [email protected] and ask for a copy. It's too big to load on this site.
  4. Replies
    12
    Views
    83

    Re: 2011 BF225 forward gear missing tooth

    BTW - that mid-shaft bushing seldom fails on 200's & 225's built after mid-2007. Honda redesigned the midsection so more lubricating water gets to it.
  5. Replies
    12
    Views
    83

    Re: 2011 BF225 forward gear missing tooth

    Agree with needing a complete rebuild. If you want to assess the level of difficulty, start reading at Chapter 12, Page 14 of the shop manual. Link to a copy is attached below....
    ...
  6. Re: BF225 intermittent stuttering and shaking at idle

    OK. Are you saying now that the engine is running fine except for just at startup?

    Going back to your video, when the engine starts shaking it sounds like you are losing rpm's. Do you have a...
  7. Re: 2002 BF225 Intermittent Power Loss and Bucking

    That last is an interesting question and I do not have a definitive answer. However, the Helm shop manual says that "Fuel cut solenoid valve is controlled according to engine temperature, speed and...
  8. Replies
    2
    Views
    32

    Re: BF 225 Fuel Flow Issues

    Those HP fuel pumps seldom fail, so try to eliminate other issues before spending the big bucks (and time) to replace.

    Make sure you don't have a kinked or restricted fuel line - check them all -...
  9. Re: BF225 intermittent stuttering and shaking at idle

    Gas smell is not good! I assume that the gas smell is coming from under the engine cover - is that correct?

    Find out where it's coming from. You could be sucking air into the fuel. Turn on the...
  10. Re: 2002 BF225 Intermittent Power Loss and Bucking

    Eleazar88 - Roger that on bypassing the Racor. If that didn't help, then I was parking up the wrong tree. Still, I would run that clear plastic line from the LP filter to the LP fuel pump just to...
  11. Re: 2002 BF225 Intermittent Power Loss and Bucking

    Yes, by all means do a compression test and adjust valves.

    BUT - your description indicates a fuel flow problem. I've never heard of a Racor filter bowl popping off, so that makes me very...
  12. Replies
    1
    Views
    71

    Re: O ring alternative that buy you beer

    metal-chicken. Good info. Thanks for that.

    For US purchasers, here is a link to the same thing: https://www.theoringstore.com/store/index.php?main_page=product_info&products_id=1914

    17 cents...
  13. Re: 15hp outboard honda 2004 power to motor but dead and no trim or tilt as well

    While you are doing that, rapidly bend each cable back and forth. If you hear a crackling sound, the cable is corroded inside under the sheath. Replace it.
  14. Replies
    2
    Views
    94

    Re: Outboard Height Position

    The basic rule is that the engine's anti-cavitation plate (correctly, the anti-turbulence plate) should be even with the lowest point of the transom. That holds if the engine is mounted directly on...
  15. Replies
    9
    Views
    115

    Re: Frozen screws for motor covers BF20D

    Perseverance Pays! Good for 'ya.

    I use CRC 6-56 as a corrosion blocker on my outboard (and fishing rods and reels, too.)
  16. Replies
    9
    Views
    115

    Re: Frozen screws for motor covers BF20D

    Keep working the PB Blaster. I've had some that have taken several days to get them to budge. Once you soak heads in PB Blaster, fit a correct fitting screwdriver or dowel on the head, and tap it a...
  17. Re: BF225 overheating at idle but not at higher revs...

    James t - good explanation. Thanks for that.

    The USCG was putting 5,000 - 6,000 house on these engines. BUT, they were running them almost every day except when they were in the shop for...
  18. Re: BF225 overheating at idle but not at higher revs...

    That's OUTSTANDING! How long did it take you to change out the oil pan and get it all back together? Any observations for anyone facing a similar task?
  19. Replies
    4
    Views
    169

    Re: Original boat decals wanted

    Go to West Marine. They make all kinds of boat decals and may have the ones you need in their computer. It may be best to call them. 1-800-262-8464
    ...
  20. Replies
    12
    Views
    414

    Re: BF130 bearing carrier wont budge

    Here's a link to an online manual for the 115A and 130A.

    https://www.feuerwehr-krems.at/Dokumente/Bezirk/Die%20Sachgebiete/Wasserdienst/AGBoot/Werkstatthandbuch-Honda-BF130.pdf
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4