Logo

Search:

Type: Posts; User: Jerryjerry05

Page 1 of 4 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    1
    Views
    10

    Re: No spark/ fuse somewhere

    Every Bayliner I've worked on had a fuse block under the dash?
    The wiring diagram for the boat??? Contact Bayliner
  2. Re: Chrysler 60ís 70hp remote control cable install issue

    Video?
  3. Replies
    11
    Views
    813

    Re: 1996 force 75 lower unit

    Mikesouth you need to start your own thread.
    Go to the Chrysler Force forum and look for the thread starter.

    boatsdotnet is a good place to look or Franz Marine.
    There are a few on ebay



    ...
  4. Re: Chrysler 75hp Bearing Cage or Lower Unit

    Look up "outboard salvage yards" "outboard salvage" "antique outboards"
    "Chrysler outboard used parts"
    I know there's a lot of old motors in yards in the mid-west. Google
  5. Re: 1996 Mercury Force 40 ELPT two cylinder flywheel torque

    85-90#
  6. Re: Chrysler outboard only running on one cylinder

    Pack is the CDI module.
  7. Re: Chrysler outboard only running on one cylinder

    NO FIRE OR INTERMITTENT ON ONE CYLINDER:


    Check the stator resistance, you should read 680-800 ohms (factory) and 400 —500 (CDIIRAPAIR) DVA 180V or more from blue to yellow (Note — On some two...
  8. Re: Chrysler outboard only running on one cylinder

    What ignition system do you have? Picture of the components?
    You need to use a photo sharing site to add pics.
    After 5 posts you can add them.

    Prestolite ignition? or the original Chrysler ??
  9. Replies
    3
    Views
    73

    Re: Control cables

    Yes buy a Mercury style shifter and cables. :(
    You'll also need the newer style wiring harness too. :(

    What style shifter do you have? side mount?

    Ebay is a good bet.
  10. Replies
    2
    Views
    72

    Re: 1984 Chrysler 140 Outboard

    The original wires came in pieces, the end, called a "sparkie with spring" $6-7 each, still available.
    The wire is NLA so use 7 or 8mm what ever fits best.
    They do sell the sparkie here and other...
  11. Re: Wanted 1996 Gamefisher / Force 9.9 Steering Bracket

    The part fits Mercury and Force and Chrysler and Sears and a few more.
    Maybe try Google for Marine Salvage or Outboard salvage.
    In the Midwest there are a bunch of salvage yards.
    Good hunting!!
  12. Replies
    1
    Views
    154

    Re: Fuel tank capacity

    The one I had was 102gal.

    Those kind of questions can best be answered by Bayliner.
    Send them your questions and include the hull ID#
  13. Replies
    5
    Views
    203

    Re: Does quicksilver make Force parts?

    There are 2 on ebay
    Starting at $56 with free shipping.
    This probably won't pay shipping to AU???

    Can you find a junk outboard yard or marine salvage?
  14. Replies
    5
    Views
    203

    Re: Does quicksilver make Force parts?

    boatsdotnet??
    eBay ?
    What parts?
  15. Re: 1978 85 hp Chrysler with 1991-1994 90 hp Carbs

    The float needs to be flat, no light.

    Seems like the bigger the jet, you'd run rich?
    I'm not a carb expert by any strech.:0
  16. Re: 1978 85 hp Chrysler with 1991-1994 90 hp Carbs

    The idle air jets don't affect anything but the way it runs at idle.

    Floods and dies or runs out of gas?
    Seems the smaller jets would restrict the intake???
    What rpm's at idle, in gear, in the...
  17. Replies
    2
    Views
    170

    Re: 95 Force 120 ignition switch wiring

    Try over on iboatsdotcom the Force forum.
  18. Re: 1994 Force 40 HP by Mercury Marine prop interchange

    https://www.miwheel.com/outboard-propellers/outboard-sizing-analysis/
  19. Re: force 40...merc or chrysler?? Need prop

    Your correct!!!
    Now go to Michigan Propeller and figure out the right pitch.
    https://www.miwheel.com/outboard-propellers/outboard-sizing-analysis/
  20. Replies
    5
    Views
    203

    Re: Does quicksilver make Force parts?

    In the early 90's Mercury(Quicksilver) bought Force.
    Then they started putting their name on everything.
    Then they started putting their parts on the motors 91.
    In 95 they went to their systems...
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4