Logo

Search:

Type: Posts; User: footbrake

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    668

    Re: Prop Shaft Size

    350 Mercruiser with a Borg/Warner Velvet Drive 1:1 ratio
  2. Replies
    3
    Views
    668

    Prop Shaft Size

    Would anyone know the diameter of the prop shaft on my 1983 Chris Craft 251 Catalina? Thanks
  3. Thread: Seacock??

    by footbrake
    Replies
    2
    Views
    1,771

    Seacock??

    What exactly is a seacock? On my Chris Craft Catalina 251 , my marina says that there are some drips coming from my seacock and that maybe I should replace it next season. Thanks-Russ
  4. Replies
    1
    Views
    1,269

    Trim tab trouble

    On my 1983 Chris Craft Catalina 251 which I purchased Last spring, the previous owner told me the trim tabs weren't working. I didn't bother with them last year or most of this year but had a chance...
  5. Replies
    5
    Views
    2,068

    Re: Exhaust fumes in cabin?

    I have opened the hatches when docking and there are no exhaust fumes or gas smell in the bilge at all. No exhaust leak
  6. Replies
    5
    Views
    2,068

    Exhaust fumes in cabin?

    Here's something that has been happening this year. I have a Chris Craft 251 Catalina, inboard ,350 mercruiser. I've notice a strong exhaust fume smell in the cabin area when I dock the boat after...
  7. Replies
    7
    Views
    2,130

    Re: Fuel tank removal

    Here is a pic of what I'm dealing with. As you can see it looks like I may be able to slide it out with some persuasion17228
  8. Replies
    7
    Views
    2,130

    Re: Fuel tank removal

    2 reasons for pulling it. First I have to remove it to put on my swim platform. Need to thru bolt the brackets with starboard backing plates. Second, I need to replace the sending unit as it's not...
  9. Replies
    7
    Views
    2,130

    Re: Fuel tank removal

    17225It goes across the back of the boat from the thick blue trim line to just above North Tonawanda NY. It is completely visible from the inside below the deck, under the floorwhere the engine and...
  10. Replies
    7
    Views
    2,130

    Fuel tank removal

    Has anybody had to pull the fuel tank out of a Chris Craft Catalina 251. I'd like to know a good way to do this without too much trouble
  11. Replies
    3
    Views
    3,276

    Re: What Trans do I have?

    Sorry, but it's shrunk wrapped for the winter
  12. Replies
    3
    Views
    3,276

    What Trans do I have?

    How do I tell what trans I have in my boat? It's a 1983 Chris Craft Catalina 251. The original 305 engine was changed to a Mercruiser 350 some time before I bought it.
  13. Replies
    3
    Views
    2,033

    Re: Painting over old Gel Coat

    Interlux Brightside 1 part Polyurethane. Tons of colors and just roll it on and tip it with a brush. Will come out like a spray job
  14. Replies
    3
    Views
    3,522

    Re: Steaming 350Q

    Seems to be the norm for these CC's. I replaced both risers and manifolds, new thermostat, new impeller, new circulatory water pump on my 251 with 350 a Mercruiser . It still blows some steam. I...
  15. Replies
    1
    Views
    2,673

    Using Brightside one part finish

    From the bottom stripe of my boat to the waterline is about 4". It is painted with ablative bottom paint as is the whole bottom. After about a month in the water( I keep it docked all summer) it...
  16. Replies
    3
    Views
    3,813

    Power Inverter Question

    I have a small 1500 watt inverter on my boat that I use for small stuff like a vacuum and trouble lights if need be. My question is, can I mount and hard wire it to one of the batteries so I don't...
  17. Replies
    3
    Views
    421

    My marina is too busy?

    Well my marina is contracted every year to pull the boat, power wash the bottom, change the fluids and winterize the engine, shrink wrap it and store it. This week I asked if everything was done and...
  18. Replies
    6
    Views
    10,393

    Re: Depth finder problem

    Would there be a way to adjust the transducer to read correctly all the time or is this just the nature of the animal?
  19. Replies
    6
    Views
    10,393

    Depth finder problem

    Don't know if I have the right forum for this but here goes. I have a hummingbird fish/depth finder. It's a small cheaper one. When I'm just cruising under 15 mph the depth and temp numbers are...
  20. Replies
    4
    Views
    574

    Re: Zerk fittings on outdrive

    11170
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4