Logo

Search:

Type: Posts; User: racerone

Page 1 of 4 1 2 3 4

Search: Search took 0.14 seconds.

  1. Replies
    6
    Views
    56

    Re: 1998 200hp Flywheel removal

    If magnets are not broken they can be re-used.-------Just make sure you put them back in the same way ( one at a time ) so poles stay the same.------Use factory epoxy kit.----Measure that gap or use...
  2. Re: Near new motor, not throttling up, need help....

    Serial # is ??----Check reed valves.----If that is good , your local repair shop can help I think
  3. Replies
    6
    Views
    56

    Re: 1998 200hp Flywheel removal

    Buy a good puller if you have to.-----No timing issues to worry about.------Get the factory epoxy repair kit.----Easy fix in my opinion.
  4. Re: Near new motor, not throttling up, need help....

    Motor should be stored with carburetor empty.----Empty carburetors stay clean.------I suggest you clean the carburetor.
  5. Replies
    13
    Views
    110

    Re: Identifing a supposidly vacuum hose.

    I guess I missed the part about your 40 years of experience in post #1---------Good luck with your project.
  6. Replies
    3
    Views
    52

    Re: popin outa gear

    They used to say----" Need a new spring and hub ".------It has been discussed at length on this site and others as to how you can repair it.----As long as it has not been abused !----I discovered /...
  7. Replies
    6
    Views
    99

    Re: Prop Question?

    The 3 blade will work better.
  8. Replies
    13
    Views
    110

    Re: Identifing a supposidly vacuum hose.

    The original fuel pump was inside that can.------This outboard powerhead needs to comply with coastguard guidelines / rules for an inboard engine.
  9. Replies
    6
    Views
    99

    Re: Prop Question?

    Sounds like the motor might be running on 1 cylinder.-----Do compression test .----Post the numbers.-----Does spark jump a gap of 1/4" or more on both leads?
  10. Replies
    9
    Views
    136

    Re: 1994 70 HP EVINRUDE Need help please

    There was a service bulletin that came out in 1994 to move the tell tale fitting to the top of the block.-----But good luck getting this motor sorted out.
  11. Replies
    15
    Views
    393

    Re: Starting Issue - '68 Merc 350S

    Deleted
  12. Replies
    15
    Views
    393

    Re: Starting Issue - '68 Merc 350S

    That starter is quite common.------One from a 50 HP will likely fit.------What part # is the starter you have and where did you buy it?----Online I assume.
  13. Replies
    9
    Views
    136

    Re: 1994 70 HP EVINRUDE Need help please

    If the red lever is in the wrong position it will allow too much fuel into the engine.----Have you installed the latest water pump repair kit ?------Does spark jump a gap of 3/8" or more on the 3...
  14. Replies
    5
    Views
    107

    Re: no spark on one cylinder

    Why did you install all these new parts ?------Contact parts supplier for warranty.
  15. Replies
    9
    Views
    136

    Re: 1994 70 HP EVINRUDE Need help please

    There are 2 small hoses that come off the primer valve.-----When motor is cranking the key is pushed in.-----Fuel is then sprayed into the air as it goes into the motor.----This fuel bypasses the...
  16. Replies
    9
    Views
    136

    Re: 1994 70 HP EVINRUDE Need help please

    It needs a simple repair kit.--------Fuel from the primer valve does NOT go into the float bowl,
  17. Replies
    9
    Views
    136

    Re: 1994 70 HP EVINRUDE Need help please

    The electric primer valve is a wonderful / simple / reliable item.-----Learn how it works as you need it for cold starting !----Fuel from this primer valve does NOT go to the carburetor bowls.
  18. Replies
    15
    Views
    393

    Re: Starting Issue - '68 Merc 350S

    your location?
  19. Re: 1997 Evinrude 90 Slight Hesitation at WOT

    Keep reading your service manual.-----It will guide you to the issue.
  20. Re: 1997 Evinrude 90 Slight Hesitation at WOT

    Motors need a new water pump impeller about every 5 years.----Has that been done ?
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4