Logo

Search:

Type: Posts; User: Docksidemarineservices

Page 1 of 4 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    11
    Views
    45

    Re: mercury 5hp 4 stroke

    Run it dry. The few seconds of dry running will not harm anything...
  2. Replies
    14
    Views
    58

    Re: 4.3L Intake Manifold

    Tap it with a hammer.... It will show you its condition. Not repairable.
  3. Replies
    5
    Views
    39

    Re: Yamaha 250 cr

    Over the years people have been asking if this can be done across all make out boards.... DTS or Mechanical.... Just trying to explain that the CR lower(LH) is built different than the SR...
  4. Replies
    5
    Views
    39

    Re: Yamaha 250 cr

    You can and you need to change the shift cable position in the control box... and get a RH prop.
  5. Re: How to Freshwater Flush an Alpha One While In the Water (No Muffs)

    Read post #3 again.
  6. Re: over heating problem new pump and tstats did not help

    Inferred temp gun..... Check on the engine side of the t-stat housing.
  7. Re: over heating problem new pump and tstats did not help

    When you checked the popit, did you make sure the seat for the valve was knocked all the way in the exhaust adapter? If it is not the engine will over heat....

    Check your cylinder heads when...
  8. Re: How to Freshwater Flush an Alpha One While In the Water (No Muffs)

    Too much thought is put into flushing engines....

    I have a customer who had me install Quick silver flush kits on his 2016 SeaRay SLX W/Mercruiser 350 Mag MPI/EC engines when the boat was brand...
  9. Replies
    8
    Views
    100

    Re: Mercury gear oil in Honda

    You can use the Merc Hi Perf gear oil in your Honda..... I use it in everything except Yamaha HD lowers and Volvo Penta Drives....

    I even use it in my Strange Built rear axle in my car.
  10. Re: 2019 Mercury Verado V8 oil leak and fuel sheen

    There is a bulletin on Four stroke Merc outboards.... Do not store them with the engine in the down position. Oil will sit on the back side of the piston in the bore and pass the rings causing oil...
  11. Re: 2006 292 Fastech manual opening of engine hatch?

    Look around the hatch/seat, there will be a plate giving you access to pull the pin on the actuator rod connection.
  12. Replies
    5
    Views
    91

    Re: Ive searched everywhere!

    https://www.boats.net/product/accessories/7670-BRP-MOTOR-E6RG4
  13. Re: motor hard starting after sitting a month

    Correct terminology: The Oil tank on the engine is the "Main Oil Tank"

    The tank mounted in the boat hull that you fill is the "Reserve Oil Tank"

    You remove the cap from the reserve oil tank.
  14. Re: Low Voltage Fault Verado 300 2012

    Low voltage can be on the 5v reference.....
  15. Re: motor hard starting after sitting a month

    Did you check every thing listed above?
    Follow the hose, you will find the valve.
  16. Re: motor hard starting after sitting a month

    Part Number 8781051

    http://www.marineengine.com/newparts/part_details.php?pnum=MER21-8781051
  17. Re: motor hard starting after sitting a month

    Run your engine up to temp, shut it off, wait a few minutes (5-10) and remove the oil fill cap and listen for air purging....

    If air purges, change the oil tank pulse/check valve. You will find...
  18. Re: 1996 Mercury 225 outboard - engine dies in gear

    You know as well as I, a majority of the time, the o-rings leak only after the engine has been cooked.
  19. Re: 1996 Mercury 225 outboard - engine dies in gear

    Borrow a bore scope and look inside the plug hole before you pull it apart.
  20. Re: 2000 Yamaha f115TLRY wont got to full throttle

    These things happen....
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4