Logo

Search:

Type: Posts; User: racerone

Page 1 of 4 1 2 3 4

Search: Search took 0.13 seconds.

  1. Replies
    7
    Views
    45

    Re: What is the best way.

    Is the electric primer valve opening ?----Have you looked at the FILTER in the electric primer valve ?----I repeat , this motor in good condition will start right up in 60 degree weather.----Cars...
  2. Replies
    7
    Views
    45

    Re: What is the best way.

    Nope----That motor has no issues starting in 60 degree weather , if in good condition !!-----Are you pushing the key in and holding it in for starting , yes or no ?----Check battery cables too.
  3. Replies
    7
    Views
    45

    Re: What is the best way.

    Why all those ignition parts ??-----Are you pushing the key in and holding it in WHILE cranking it over ??-----Hard starting can also be due to a bad battery -----Have it load tested even if...
  4. Replies
    2
    Views
    26

    Re: 1983 mercury shift/throttle issues...

    The shift cable is the first one that moves shifting from neutral.----You are sure the cables are on correctly ?
  5. Re: Honda 5hp 4strk compression of 65psi…

    How did this motor run for you last season ?-----Or another " Aquasition " to flip for some beer tokens ?
  6. Re: Honda 5hp 4strk compression of 65psi…

    Does this motor have a compression release feature ?
  7. Replies
    1
    Views
    22

    Re: Thermal Switch

    Part of the choke system.------Thermo-electric choke.
  8. Replies
    3
    Views
    31

    Re: Temperature Gauge

    Have you tested the warning horn in the control box ?----If yes , was it not loud enough for you ?
  9. Replies
    14
    Views
    113

    Re: Electric Sift Questions

    ???----Well ---1972 was the last year they were produced / marketed.----And I know that all too well !----Spare parts were available and the lower unit might have been installed in 1980 !----I would...
  10. Re: Johnson 1998 2cyl 2strk 50hp Lower Unit - R and FWD not working

    Bearing housing in 3rd picture is SCRAP.-----Unless you are well versed in machining.----All bearings should be replaced.
  11. Re: Help: Drive Shaft won't come out of lower unit!

    I have said it many times.-----These lower units are not robust !!
  12. Re: Help: Drive Shaft won't come out of lower unit!

    Screw #3 prevents the pinion bearing from rising due to oil pressure.----It needs to be removed because you are installing a new bearing I hope.----#3 does not need to come out to pull the driveshaft...
  13. Replies
    11
    Views
    45

    Re: mercury 5hp 4 stroke

    Carburetors that are empty stay clean.
  14. Replies
    2
    Views
    36

    Re: Evinrude 35hp woes

    Water in your test tank MUST be 8" above the impeller.-------Take starter apart and inspect.-----Might just need new brushes.-----Of course if money is not a problem you can rush out and buy a new...
  15. Replies
    14
    Views
    113

    Re: Electric Sift Questions

    Doubt that the V-4 units will fit on a 3 cylinder model.
  16. Re: No Spark? 89 15hp tiller. Bypass Kill switch test.

    Disconnect the ground wire.-----Check flywheel key ( alignment ) through plug hole.-----Should line up timing mark with top piston at TDC.
  17. Replies
    11
    Views
    86

    Re: 1999 BF 15A fuel pump

    About the only thing that can go wrong is the diaphragm.----Available new I believe.--About $25.
  18. Replies
    11
    Views
    86

    Re: 1999 BF 15A fuel pump

    I guess I missed the new tank / hose in the first post.----There likely is a pump that will fit.----- I do not have the expertise today to look for you.
  19. Replies
    11
    Views
    86

    Re: 1999 BF 15A fuel pump

    Test run with another tank and hose.----Some will argue , but I would take the pump apart.-----Possibly make a new diaphragm.----Inspect check valves for dirt.-----Simple in my opinion.
  20. Re: Why doesn’t my 89 15HP have and idle adjust screw?

    Doubt you will find a screw under the flywheel on an 89 model.
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4