Logo

Search:

Type: Posts; User: bondo

Page 1 of 4 1 2 3 4

Search: Search took 0.04 seconds.

  1. Re: 1962 Chris Craft 283 rebuild. Oil filter canister change out.

    Ayuh,..... I guess it depends on the adapter you choose, if it has a built-in by-pass, or not,.....
  2. Replies
    6
    Views
    59

    Re: What am I looking at here?

    Ayuh,..... If the thingy with the wires on one post, has a reset button on it, it's a circuit breaker,......

    Boats use a slave solenoid to excite the starter's solenoid, rather than straight...
  3. Replies
    6
    Views
    59

    Re: What am I looking at here?

    Ayuh,..... Donno what that is with the single wire on it,......
    The slave solenoid is the other thingy with the other red cables attached to it,.....
  4. Replies
    5
    Views
    74

    Re: Winterizing a non-running I/O

    Ayuh,..... Air don't freeze, so drained dry is how I winterize,.....

    'n don't forget the P/S cooler if so equipped,.....
  5. Re: Boat lifting Ideas for Trailer repair and bottom paint work

    Ayuh,..... You only need 2 stacks of blockin' under the transom, 'n a single stack under the keel,.....

    Racerone explains the process quite clearly,..... just as I've done many times, from...
  6. Thread: gimbal bearing

    by bondo
    Replies
    17
    Views
    232

    Re: gimbal bearing

    Ayuh,.... Ditto,...... Don't wanta destroy yer new motor,.....
  7. Replies
    6
    Views
    119

    Re: Fuel Gauge and water exiting the engine

    Ayuh,..... Agreed,.... You've got a very rotten hull,.....
  8. Replies
    1
    Views
    47

    Re: Cam for reverse rotation 289?

    Ayuh,..... Maybe yer cam is still Ok,....
    Switchin' to a 4bbl. carb doesn't mean you need a different cam,....
  9. Re: Ignition switch replacement screw type connections

    Nope,....
  10. Replies
    2
    Views
    93

    Re: Electrical puzzle

    Ayuh,..... Sounds like corroded connections,.....
    Start at the battery, 'n clean the terminals, 'n cable lugs on both cables, on both ends,....
  11. Replies
    1
    Views
    209

    Re: EZ Loader trailer Repair

    Ayuh,.... Brakes on one axle is typical,.....
    You need to find the part numbers off the bearings, 'n seals,.....
    The fact that it's an ez loader don't really matter,.....
    'n for the price of 32...
  12. Replies
    5
    Views
    80

    Re: ignition sw. mystery

    Ayuh,..... Sounds like a bad switch,.....
    The purple wire is the ignition circuit,.... Check for power at the coil's (+) tiny terminal,.....
  13. Replies
    3
    Views
    76

    Re: 3 Belt vs Serpentine

    Ayuh,..... It'll cost a ton of money for the brackets, 'n pulleys, with absolutely no pay back,......
  14. Re: Mercruiser 350 mag closed loop showerusing raw water heating

    Ayuh,..... There should be a 1/2" pipe plug in the intake manifold just aft of the t-stat housing for the hot water tap,....
    'n there should be a 1/2" pipe plug in the circulating water pump...
  15. Replies
    3
    Views
    210

    Re: Are marine engine blocks unique

    Ayuh,..... Exactly,.....
  16. Re: Shift interupter switch won't move enough to engage the kill function

    Ayuh,..... Sounds like an ole MC-1, the reverse lock,....

    Don't try to trim it in reverse,....
  17. Re: any ideas on getting a starter out of a 5.7 when the bolt heads are stripped studs frozen?

    Ayuh,..... No Doubt, pull it, 'n get it over with,.....
    The smaller headed bolts only came to be, maybe 10 years ago,....
    Prior to that, 9/16" was standard issue,.....
  18. Re: 1982 Yamaha 55hp C55ELRQ no Reverse with exceptions.

    Ayuh,..... Sounds like a controller problem,.....

    Are the cables movin' as they should be, or are they workin' as you explain, at the motor, under the cover,..??
  19. Re: changing a 318 standard rotation engine to a reverse rotation engine

    Ayuh,.... The seals are in fact different,.....
  20. Thread: 3.0 engine swap

    by bondo
    Replies
    2
    Views
    103

    Re: 3.0 engine swap

    Ayuh,..... Do the couplers bolt to the flywheel, or the crankshaft,..??
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4