Logo

Search:

Type: Posts; User: bcclew

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Thread: Anchor windless

    by bcclew
    Replies
    1
    Views
    104

    Re: Anchor windless

    1/4 is corect link size just under an inch no bigger thanks
  2. Thread: Anchor windless

    by bcclew
    Replies
    1
    Views
    104

    Anchor windless

    2002 26ft searay marlin windless chain slips once inwhile i took off gypse says 1/4 inch. I used micrometer i measured link thickness its 3 thousand larger. But how do you know the width of the...
  3. Replies
    0
    Views
    75

    Borgwarner v drive

    Ratio? E.2.0 what does that mean or 1.5.1 i am looking to change borgwarner v drive this is in 1976 26 ft silverton 5.7 how much of a difference would either make?runnig the boat ? The one...
  4. Replies
    0
    Views
    226

    2006 yamaha 50t 4 xtroke

    I was told sharder valve on top of vst tank is to let air in when draining vst tank? Special tool needed ro ck fuel pressure? Thanks
  5. Thread: Vdrive

    by bcclew
    Replies
    2
    Views
    569

    Re: Vdrive

    Ok you can do this in the boat if you have access to a boom truck lift it out you can now work comfortable I did it myself but I am only 170lbs I could fit thanks for readind
  6. Thread: Vdrive

    by bcclew
    Replies
    2
    Views
    569

    Re: Vdrive

    Anybody know the size of the flange nut. Is it 1&7/16? Thanks
  7. Thread: Vdrive

    by bcclew
    Replies
    2
    Views
    569

    Vdrive

    1976 silverten borg warner velvet trans and v drive its all one unit. Has ony one change the prop shaft flange seal.l think i canget the sfaft back enough to get at that big nut.any helpwould be...
  8. Replies
    1
    Views
    606

    Re: Seakamp ,4"" end cap

    36 to 72 inch lbs
  9. Replies
    1
    Views
    606

    Seakamp ,4"" end cap

    Anyone know the torque spec thanks
  10. Thread: Cables

    by bcclew
    Replies
    4
    Views
    288

    Re: Cables

    ok thanks
  11. Thread: Cables

    by bcclew
    Replies
    4
    Views
    288

    Cables

    1976 28 ft silverton with 2 crusaders 5.0 replacing shift cables 2 do the universal cables work ? J am changing ables from down stair helm these are factory controls not sure about cables has...
  12. Thread: bottom paint

    by bcclew
    Replies
    0
    Views
    219

    bottom paint

    any body around Barnegat bay had power washed for winter they always do a good job.this time it looks like a leopard spots.checked a few other boats at marina the have them too.their smooth from the...
  13. Replies
    1
    Views
    525

    1974 318 distributor

    is any body using the complete after market kit .with every thing new just hook up 2or 3 wires and set base timing. i have used the gm ones they work great.or trouble check this system? thanks
  14. Thread: float switch

    by bcclew
    Replies
    2
    Views
    345

    Re: float switch

    ok ill try it thanks
  15. Thread: float switch

    by bcclew
    Replies
    2
    Views
    345

    float switch

    this maybe crazy i changed float switch with a rule same as i had before. i think with the old switch it would come on and pump out.as the float hit the bottom.it seemed to run for a few seconds.this...
  16. Thread: Trans type

    by bcclew
    Replies
    3
    Views
    146

    Re: Trans type

    Thanks
  17. Thread: Trans type

    by bcclew
    Replies
    3
    Views
    146

    Trans type

    1996 silverton 31ft 454 mercs v drives what trans is most popular?tanks
  18. Replies
    2
    Views
    251

    Re: No one cyl 2014 yamaha v8

    Thanks
  19. Replies
    2
    Views
    251

    No one cyl 2014 yamaha v8

    Faceing the bow of the boat standing behind the engine where is number one port or starbord top or bottom? I downloaded mznual gives cireing order but not positionof number 1 cylthanks
  20. Thread: shore power

    by bcclew
    Replies
    6
    Views
    1,847

    Re: shore power

    thanks gu7ys
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4