Logo

Search:

Type: Posts; User: Docksidemarineservices

Page 1 of 4 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    21
    Views
    407

    Re: Merc 260 issues

    Me personally, I would pull the dip tube and anti siphon valve from the tank and take a good look.
  2. Re: Mercruiser VesselView4 - Low Voltage Warning

    You will be checking the 5v reference circuits when you get your scan tool.... (Power1 and Power 2)
  3. Re: Yamaha LZ150 HPDI Runs only when Key held in the start position.

    That is the plan, I will be hauling it and blocking it on Monday for easier access.
  4. Re: Yamaha LZ150 HPDI Runs only when Key held in the start position.

    Problem not solved with remote key switch..........
    At this time of the year I have a stack of boats to service and not much time to dig into this engine harness/ecm, hoping someone would give me a...
  5. Re: Engine swapping compatibility?

    You will not save fuel by downsizing your engine, you will burn more.
  6. Yamaha LZ150 HPDI Runs only when Key held in the start position.

    LZ150 only runs when key held in the start position, engine dies when key released to the run. Nothing wrong with the key switch. I divorced the engine from the boat harness and used a remote key...
  7. Re: looking for measurements for v/p sx-a trim pistons

    They have different degrees of tilt as to not damage a swim platform.

    FULL TILT 52 DEG. 23 13/16" FULLY EXTENDED

    42 DEG. TILT 22 3/8" FULLY EXTENDED

    32 DEG. TILT 20 13/16" FULLY EXTENDED
    ...
  8. Re: looking for measurements for v/p sx-a trim pistons

    There are 3 different trim pistons for the VP SX-A..... 32 degree 42degree and a full tilt 52 degree.
  9. Re: Loss of rpm on 5 liter mercruiser

    Here is an over looked issue..... How much oil is in the crank case?
  10. Re: 2001 Yamaha 130 2 stroke - hard to start

    If the engine idles once started and runs as it should, the carbs are fine. Hard starting on an V4 Yamaha two stroke with a mechanical choke is usually a bad fuel pump(leaking into the crank case),...
  11. Re: 2014 Yamaha 115hp not enough amps to start motor

    Grab the rigging cable,(battery Cable) put it next to your ear and bend it. Does it crackle? Yes, the cable is bad. Common.
  12. Re: Upgrade an oldl B2 to a B3 duoprop

    The X dimension is different between the B2 and B3. Fix your drive. Simple repair.
  13. Re: Canít remove drain bolt or gear case oil screw on Honda 75HP

    Do not use a torch, no matter what.
  14. Replies
    2
    Views
    178

    Re: BF200A cutting out

    First thing to inspect. Where the rigging comes into the engine cowling, remove the hold down for the cables, fuel line, battery cables ect.. an look for corrosion that is pinching off the fuel line....
  15. Re: Voltage Regulator Rectifier

    I would use OEM or CDI. Not the cheapest one on the internet. Marineengine.com, where you are asking for advice, is where you should get your parts.
  16. Re: Voltage Regulator Rectifier

    Common issue. Replace it.
  17. Re: 671 TI Detroit dead spot in acceleration

    Is the name on this boat "Hold fast"?
  18. Re: 671 TI Detroit dead spot in acceleration

    Why do I feel like I know this boat. Can you post a picture?

    2X's on the injector rack.... Check boost, check linkage......
  19. Replies
    6
    Views
    249

    Re: Milkshake from BF130

    Pressure test it. You will see what is leaking.
  20. Re: Mercruiser 7.4 L Mpi L29 MISS FIRING in Bayliner 2855 Cierra

    The IAC goes open when running at cruise speed. So it should not cause a surge at cruise speed.
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4