Logo

Search:

Type: Posts; User: snookwhaler

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Re: Taking 2006 Mercury Into Shop. Worried!

    It just slides out. No tools required.

    The gear and bearing will need to be pressed off the shaft though if you're replacing the shaft.

    Be careful when you pull the shaft out, there is a pin...
  2. Re: 2002 Mercury 40hp efi overheating alarm

    You should make that part of your annual maintenance. They get clogged with crud, they can get stuck and the cages can actually corrode away over time.

    Also, if they have not been removed for a...
  3. Re: 2002 Mercury 40hp efi overheating alarm

    When is the last time you pulled the thermostat?
  4. Re: 55 hp mariner marathon rev counter issues

    The grey wire in the harness connector is the tach signal wire. If I remember correctly and if you are able to hook up a harness to your plug, grey is the tach signal, purple is the 12v switched...
  5. Re: 1996 mercury offshore impeller questions

    If the engine is new to you, checks out OK (good compression, runs good, etc...) it's best to change out the water pump and inspect the T'stats before you use the engine, IMO...

    You have no idea...
  6. Replies
    5
    Views
    239

    Re: timing 2.5 mercury 150 XR6

    You should post this over on Scream and Fly.
  7. Replies
    4
    Views
    238

    Re: Overheat alarm test

    Yep. It works. Thanks.
  8. Replies
    4
    Views
    238

    Re: Overheat alarm test

    Thank you. That's what I thought, but was not sure.

    That is the one in the back of the head. I removed the screw and tried to pry it out. But, It's really in there. Will I damage anything if I...
  9. Replies
    4
    Views
    238

    Overheat alarm test

    2005 Merc 60hp ELPTO.

    Is there and easy and quick way to see if my overheat alarm is working?

    I just removed my thermostat and found the cage broken off on both sides. I put the stat in hot...
  10. Replies
    1
    Views
    133

    Re: 2001 75hp mercury oil tank

    The way I understand it, is you cannot replace just the float assy. You buy the new tank and you get the new float with it. Unfortunate, because they're not cheap.
  11. Replies
    3
    Views
    249

    Re: engine problem

    Sounds fuel related from what you describe. Try hooking it up to a portable tank with new hose and primer bulb if your able to. Newer crap fuel hose can collapse internally causing restrictions in...
  12. Re: Lower enf shift spline position wont engage - 2010 40hp bigfoot mercury

    Did you move the shift shaft on the lower unit? Does the prop still spin freely? If so, it is probably off by just a millimeter or 2. You need to manipulate the upper shift linkage back and forth...
  13. Replies
    1
    Views
    231

    Re: Torque value

    I have a 2005 60 ELPTO with the non big foot gear case and it is 15.5 lb. ft. if I remember correctly. The big foot gear case is a little more up around 20 or so.
  14. Replies
    3
    Views
    405

    Re: 90 HP Mercury Torque Specs

    Should be in here. This is where I got the info. for my rebuild.

    http://************/lib/mercury/manuals/75-90-100-115-125.html#/6
  15. Re: 2005 Mercury 60hp ELPTO need some advice

    I spent quite a bit of time on this today and I think I pretty much have figured it out. I followed the Mercury shop manual and it got me close to where I need to be. The rest is just a little fine...
  16. Replies
    8
    Views
    900

    Re: How's my idle? 2008 60HP 3 Cylinder

    Thank you. I spent some time under the cowling and on the water today and I finally figured it out. Lots of things out of whack. I got it running much better. Just a little fine tuning and it will be...
  17. Replies
    8
    Views
    900

    Re: How's my idle? 2008 60HP 3 Cylinder

    That's a massive difference! That's how there supposed to sound at idle... I had a feeling it was something to do with timing as well. Looks like you're in a different country, so doubt they will be...
  18. Replies
    8
    Views
    900

    Re: How's my idle? 2008 60HP 3 Cylinder

    Watching your video, your engine is doing the "EXACT" same thing at idle that mine is doing! I have adjusted the carbs to no end and they are "like new" inside and out. Please post your outcome if...
  19. Re: 2005 Mercury 60hp ELPTO need some advice

    Thanks for the quick reply guys!

    I adjusted them once out on the water in gear. Never could get it to where I liked it and gave up. I adjusted them lean first, then rich and then tried to find a...
  20. 2005 Mercury 60hp ELPTO need some advice

    I recently had my 2005 Mercury 60hp ELPTO powerhead rebuilt by a local reputable builder and I have some issues and questions. If anyone has any experience with this sort of thing, I sure would...
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4