Logo

Search:

Type: Posts; User: makomark

Page 1 of 4 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    4
    Views
    121

    Re: Fuel vent issue Skeeter zx22

    Good Deal & glad it worked out!
  2. Replies
    4
    Views
    121

    Re: Fuel vent issue Skeeter zx22

    I'd bet the vent line has a 'dip' (low spot) in it...any fuel entering this region will block the free flow of air as it gets displaced when fueling up (just like a trap in a plumbing drain...
  3. Re: Anti freeze leaks from Thru-hull strainer when on the hard for bottom painting.

    I'd check the port heat exchanger...if its leaking, it should (have been) be low. if so, I'd pressure test it...if you don't have the tester, most any radiator shop should be able to test it...they...
  4. Replies
    6
    Views
    224

    Re: 1989 50 HP Force Voltage Drop

    Don't forget the negative side connections while looking for your voltage drop....another thing to consider is making voltage drop measurements across each item in the high current (starter circuits)...
  5. Replies
    1
    Views
    97

    Re: 99 PCM 7.4L MPI Running Rich at Idle

    I was going to suggest maybe an injector is hung but you stated the ECU is calling for "more fuel"...assuming that's the case, across the RPM band, something is off.

    You said you "checked" some...
  6. Replies
    72
    Views
    24,668

    Re: Old Crusader O&M Manual

    sent per your post...
  7. Replies
    17
    Views
    250

    Re: Does Size Matter?

    bigger means heavier and that may not be desirable on a ski boat. The min battery rating is only for the engine...if you use accessories, you will need to factor that into the battery size as well....
  8. Re: Dropped lower unit and pulled out speedometer tube

    The pic is the gimbal housing...without the gimbal and bell housing in the way...
  9. Replies
    3
    Views
    152

    Re: What oil pan is this?

    I've never seen a cast iron oil pan on a standard production marine engine...and I can't believe the performance variants would add that much weight...

    Put a magnet to it to see if it isn't...
  10. Replies
    3
    Views
    127

    Re: Sd cards to update helix 7 and terrova

    if its formatted and the computer can read/write to it, the HELIX should be able to do the same...maybe try the you tube videos???
  11. Replies
    4
    Views
    180

    Re: Salt Neutralizing Products

    If you always flush the engine on the hose after use, I wouldn't think a one time application would be cost effective.
  12. Replies
    7
    Views
    286

    Re: winterize w/o starting - raw water side?

    I would pull the zinc plugs from the oil cooler and heat exchanger...then deal with the raw water pump - either plug the drain plugs and spin the pump over or pop the cover free. the last thing I'd...
  13. Replies
    7
    Views
    230

    Re: Hard boat steering

    you might also consider "PB Blaster", diesel oil, and "KANO KROIL"....
  14. Replies
    5
    Views
    156

    Re: Reman 4.3 mercruiser ?

    the newer ones, Gen+, all use the same cam, from the factory....independent of fuel delivery method...
  15. Replies
    7
    Views
    230

    Re: Hard boat steering

    if the steering is smooth and free and the outboard will not pivot, sounds like the outboard has not been maintained (regular lubrication). I would suspect the swivel tube is bound up by corrosion....
  16. Replies
    7
    Views
    230

    Re: Hard boat steering

    What do you mean by 'power steering'?

    A boat that small would typically just use a cable...a hydraulic steering system would be overkill - nice but not necessary.

    I would suggest disconnecting...
  17. Re: Chevy 350 fuel cooler question....Mystery barb...

    No Joy with your attachments...
  18. Replies
    6
    Views
    149

    Re: Mercruiser 4.3L Rear Engine Bushings

    Its been a while since I've done the old style rear mounts...going off memory, there's a spacer that has a chamfered - that mates with the edge on the mount...so that drives orientation...and the...
  19. Replies
    3
    Views
    152

    Re: cm 454xl fuel issue no start

    One of the first things that would help would be use of accurate descriptions.

    Another that may help your wallet is to diagnosis the issue before throwing parts at it...but that's your choice...
    ...
  20. Replies
    4
    Views
    214

    Re: Fuel line I.D - 454/8.1

    After returning to have access to my 'library', the install guide I have states they want to see less than 2 in Hg pressure drop at the fuel pump inlet.

    also of note, they recommend a shutoff...
Results 1 to 20 of 70
Page 1 of 4 1 2 3 4